Comdial Conversip EPI00G-I12 Скачать руководство пользователя страница 20

Страница: 20 / 140

Overview

Comdial

Feb ‘05

Next to a fixed
feature or
programmable
feature button

• Steady red = the feature is on.
• Steady off = the feature is off.

Note

You can find the programmable buttons

that the installer designates as feature buttons
in the same location as the DSS/BLF buttons.
Ensure that these buttons are labeled
correctly to indicate their unique features.

MUTE Button

On steady = called party cannot hear your
conversation.

INTERCOM Button

• Steady green or red = you are using your

intercom.

• Fluttering red = an LCD message is set on

your endpoint for others to receive when
calling.

• Flashing orange = someone is calling your

extension or a call is being transferred to
you.

HOLD Button

Winking green = a line is on hold at your
station (DXP, DXP Plus, FXS and FXT only).

MESSAGE-
WAITING Button

Winking red = message awaits pick up.

SPEAKER Button

• On steady (with the endpoint on hook and

busy) = speakerphone mode

• On steady (with endpoint on hook and idle)

= background music is turned on.

Содержание Conversip EPI00G-I12













































































































































Результаты поиска

Содержание Conversip EPI00G-I12

Отзывы:

Похожие инструкции для Conversip EPI00G-I12

Бренды по названию

Популярные бренды

Comdial Conversip EPI00G-I12, Руководство пользователя

Результаты поиска

Содержание Conversip EPI00G-I12

Отзывы:

Похожие инструкции для Conversip EPI00G-I12

Бренды по названию

Популярные бренды