ComAp intelilite nt amf20 Скачать руководство пользователя

Страница: 108 / 145

InteliLite

– AMF20/25, SW version 2.2, ©ComAp – September 2014 108

IL-NT-AMF-2.2-Reference Guide.pdf

Gen-set Operation States

Engine state machine

Init

Autotest during controller power on.

Not ready

Gen-set is not ready to start.
For example when shutdown alarm is active or unit is in OFF mode.

Prestart

Prestart sequence in process, Prestart output is closed.
Usually used for preheating or processes executed prior gen-set start.

Cranking

Engine is cranking.
Starter output is closed

Pause

Pause between start attempts.

Starting

Starting speed is reached and the

Idle timer

is running.

Running

Gen-set is running at nominal speed.

Loaded

Gen-set is running at nominal speed and GCB OPEN/CLOSE is closed.

Stop

Stop.
Automatic or manual stop command was issued, engine is stopping.

Shutdowns

Shut-down alarm activated.

Ready

Gen-set is ready to run.

Cooling

Gen-set is cooling before stop.

EmergMan

Emergency Manual gen-set operation.
Used for bypass the controller and engine manual start.

ManIdle

Indicates that Manual IDLE function is activated and Engine is running on Idle speed.

“Engine started” conditions

Engine speed (RPM) >

Starting RPM

AI: Oil press >

Starting POil

D+ terminal active (reached 80% of supply voltage) for minimum 1s or

Generator voltage > 25% of NomVolts Ph-N or NomVolts Ph-Ph

(any phase)

Any of these conditions will disconnect starter of the engine, however for transition to next state RPM
needs to be higher than

Starting RPM.

“Engine running” conditions

RPM > 2

RPM

Analog input Oil pressure >

Engine params

Starting POil

Содержание intelilite nt amf20


















































































































































Результаты поиска

Содержание intelilite nt amf20

Отзывы:

Похожие инструкции для intelilite nt amf20

Бренды по названию

Популярные бренды

ComAp intelilite nt amf20, Справочное руководство

Результаты поиска

Содержание intelilite nt amf20

Отзывы:

Похожие инструкции для intelilite nt amf20

Бренды по названию

Популярные бренды