ComAp InteliLite MRS16 Скачать руководство пользователя

Страница: 616 / 632

InteliLite Global Guide

616

you want to program into the module (in LiteEdit2015).

Press the OK button to start upgrade of firmware.

The firmware update process may be performed via any kind of connection including connection via the same

module in which the firmware is to be updated. The connection is reestablished again automatically when the

update process is finished.

8.3.2 CAN modules

Communication modules

616

Extension modules

621

The available communication CAN modules are:

I-LB+ - communication local bridge

The available extension CAN modules are:

Inteli AIN8 - extension CAN module with 8 analog inputs

Inteli IO8/8 - extension CAN module with 8 binary inputs, 8 binary outputs and 2 analog outputs

this CAN module can be switched to Inteli IO 16/0 - extension CAN module with 16 binary inputs and 2

analog outputs

Maximal number of CAN modules is 2. Modules are configured via LiteEdit2015. There are 2 slots for CAN

modules.

Note:

I-LB+ communication module is not configured via LiteEdit2015 into controller CAN module slot. Also

this module is not counted into maximal number of CAN modules.

Note:

It is possible to configure all combinations of CAN modules (same modules in both slots or different

modules in both slots).

Communication modules

I-LB+

616

I-LB+

I-LB+ is communication modules for communication with all devices connected to CAN2 bus. Speed for

direct/modem connection can be up to 57600 bps. I-LB+ can be connected with PC via USB, RS232 or RS485.

Содержание InteliLite MRS16

























































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание InteliLite MRS16

Отзывы:

Похожие инструкции для InteliLite MRS16

Бренды по названию

Популярные бренды

ComAp InteliLite MRS16, Руководство пользователя

Результаты поиска

Содержание InteliLite MRS16

Отзывы:

Похожие инструкции для InteliLite MRS16

Бренды по названию

Популярные бренды