background image

 

Page 12 of 16

 

INSTRUCTION MANUAL

 

LI-150C 

LINE IMPEDANCE STABILIZATION NETWORK 

 

19121 El  T oro R d   ●  S il vera d o, Ca lifo rnia  926 76   ●   (94 9)  459 - 9600    ●  com - p ower.com

 

                

 

 

      REV021317   

should  be  bonded  directly  to  an  earth  referenced  ground  plane  for 
effective  RF  reference  ground.  In  cases  where  no  ground  plane  is 
available, a mains isolating transformer shall be used. 
Please  refer  Safety  instructions  for  more  information  on  importance  of 
grounding. The grounding instructions are to be followed at all times. 

 

5.3.3 EUT power port 

The  LI-150C  has  a  Superior  Electric  Shrouded  socket  receptacle  to  power 
the equipment under test. The LISN is shipped with the matching shrouded 
pin plug for making the connections to EUT power cable. 

 

5.3.4 EMI measurement Port 

The LI-150C provides a 

50 Ω 

N-Type (female) connector to connecting the 

Spectrum  analyzer  or  EMI  receiver  for  making  conducted  noise 
measurements.  The  shielding  connection  of  the  N  connector  shield  is 
connected to the housing of the LISN and thus to ground. 
 
Note: CISPR recommends the use of 10 dB attenuator at the output of the 
LISN  measurement  port.  Also,  as  the  input  circuitry  of  EMI  receivers  and 
spectrum analyzers are extremely sensitive; it is highly recommended to use 
transient limiter in line with the cable connecting the measurement port to 
the  measuring  equipment  in  order  to  protect  the  input  circuits  from 
damage  by  high  voltage  transients.  Com-Power  transient  limiters  also 
incorporate both a low pass and high pass filter to attenuate out of band 
signals, as well as a 10 dB attenuation pad. Both, the 10 dB attenuator and 
the transient limiter are available with Com-Power. 

 
 

 
 

 

 

 

 
 
 

 

 
 

 

Содержание LI-150C

















Отзывы: