Colortronic CTT 1600 Скачать руководство пользователя страница 71

Страница: 71 / 88

8.4. Electrical connection

Observe the rules of the local electricity board.

Check that the supply voltage and the power frequency are in accordance
with the data on the name plate of the device.

The electrical connection may only be carried through or assigned by Color-
tronic service staff or by qualified staff authorized by Colortronic.

Other persons are not permitted to carry through the electrical connection.

The main switch must be freely accessible.

Ground the equipment against electrostatic charging.

Observe that the control system is still under voltage even when the
mains switch is switched off.

Regularly make sure that none of the electrical or screw connections are
loose.

Immediately after connection, check the direction of rotation of the blo-
wers (see rotational direction arrow on the blowers).

The direction of rotation should be switched in the supply line only.

The operation voltage is 400 V/3AC/PEN/50 Hz.
Special operation voltages are possible.

64.10-0233GB05

11/02

CTT 1600

Assembly instructions 8-5

Содержание CTT 1600

























































































Результаты поиска

Содержание CTT 1600

Отзывы:

Похожие инструкции для CTT 1600

Бренды по названию

Популярные бренды

Colortronic CTT 1600, Руководство по эксплуатации

Результаты поиска

Содержание CTT 1600

Отзывы:

Похожие инструкции для CTT 1600

Бренды по названию

Популярные бренды