Colortronic CTT 1600 Скачать руководство пользователя страница 64

Страница: 64 / 88

7.1. Transport and Packing

Please ensure adequate carrying capacity of the lifting equipment.
Note that the dryer system is top-heavy. Risc of toppling!

The equipment pass a rigorous operating test in the factory and are packed carefully to avoid
transport damage.

Please check packing on delivery for transport damage.

The inlet and discharge flanges are sealed with plugs, so that no dirt can enter during transport.
Plugs must be removed before assembly.

Packing materials should be disposed of according to environmental laws or reused.

Only use for transport of the equipment a suitable lifting device (e. g. a fork lift truck or a workshop
crane).

Fasten the transport cables to the eyelets of the control cabinets.

Transport must be shock-proofed and free from vibrations.

with a fork lift truck

Push the forks up to the dryer housing.

Check that the forks reach completely under the dryer housing.

64.10-8248GB01

04/02

Dehumidified Air Dryer

Transport, Assembly and Storage 7-2

Transport with a fork lift truck

Содержание CTT 1600

























































































Результаты поиска

Содержание CTT 1600

Отзывы:

Похожие инструкции для CTT 1600

Бренды по названию

Популярные бренды

Colortronic CTT 1600, Руководство по эксплуатации

Результаты поиска

Содержание CTT 1600

Отзывы:

Похожие инструкции для CTT 1600

Бренды по названию

Популярные бренды