Colortronic CTT 1600 Скачать руководство пользователя страница 55

Страница: 55 / 88

5.6. Changing the battery of the control system

This work may be carried through only by qualified personnel trained in the
field of electrical engineering.

The battery may be changed only with the control system switched on.

Open the control box by means of the control box key which is part of the supply.

Open the front door of the CPU.

Pull the backup battery with cable out of the compartment.

Plug the connector of the new backup battery into the corresponding socket in the battery compartment of
the CPU.

The notch on the

battery connector must point to the left!

Place the backup battery into the battery compartment on the CPU

Close the front door of the CPU

Close the control box.

64.10-0233GB05

11/02

CTT 1600

Maintenance 5-11

Содержание CTT 1600

























































































Результаты поиска

Содержание CTT 1600

Отзывы:

Похожие инструкции для CTT 1600

Бренды по названию

Популярные бренды

Colortronic CTT 1600, Руководство по эксплуатации

Результаты поиска

Содержание CTT 1600

Отзывы:

Похожие инструкции для CTT 1600

Бренды по названию

Популярные бренды