background image

NCS-C151 Manual Rev B 

Page 14 

 

 

In-band Repeating 

In-band repeating requires special attention to prevent one radio from 
interfering with or desensitizing the other.  Many techniques are available 
including increasing vertical and horizontal separation of antennas, shielding 
one antenna from the other and using different polarizations for each antenna.  
The specific solution will be determined by the installation environment and the 
overall operation conditions. Experimentation will be required. 

 

11.0 Contacting NCS 

 

NCS wants you to experience trouble free operation of our equipment.  If you 
have any questions, comments or need technical help, please use the following 
resources: 
 

1.  Go to the web site, 

www.collcomminc.com

. Here you will find the latest 

instruction manuals, any factory developed modifications and Frequently 
Asked Questions.  Schematics for all NCS products are available. Please 
inquire. 
 

2.  Email us at 

[email protected]

Be sure to include all pertinent 

information, e.g. make and model of radios, how they’re connected to the 
C151, detailed description of any problems, antenna and grounding 
configurations, etc. 
 

3.  Telephone us toll-free at 888-883-5788.  

 

Note: Be near your equipment and have the manuals for your radios 
available.  We will do our best to help you using our technical expertise. 

 

 

Содержание NCS-C151

















Отзывы: