5
THERMAL RELIEF VALVE
A thermal relief valve is provided to protect the pump
from overheating if the spray gun is closed for an extended
length of time or the nozzle becomes plugged. However, it is
intended to be used as a backup system and every effort
should be made to not permit the pump to heat up.
We recommend turning the pressure washer off if it will
not be used for more than five minutes. This saves wear on
the unit, reduces fuel consumption and extends the life of the
pump by avoiding heat.
SAFETY LOCK OFF LATCH
To prevent accidental discharge of high pressure water,
the safety latch on the trigger should be engaged whenever the
pressure washer is not in use. (Refer to Operating
Instructions.)
LOW-OIL SHUTDOWN
The unit is equipped with a low oil sensor. If the engine
oil level becomes lower than required, the pressure washer
will automatically shut off. (Refer to the engine manual for
this feature.) This protects your pressure washer engine from
operating without proper lubrication.
If the pressure washer engine shuts off and the oil level is
according to specification, check to see if the pressure washer
is setting at an angle that forces oil to shift. Place on an even
surface to correct this. If the engine fails to start, the oil level
may not be sufficient to deactivate low oil level switch. Be
sure the sump is completely full of oil.
SPARK ARRESTING MUFFLER
YOUR PRODUCT MAY NOT BE EQUIPPED WITH A SPARK
ARRESTING MUFFLER. If the product will be used around
flammable materials, such as agricultural crops, forests, brush, grass,
or other similar items, then an approved spark arrester should be
installed and is legally required in the State of California. The
California statutes requiring a spark arrester are Sections 13005(b),
4442 and 4443. Spark Arresters are also required on some U.S. Forest
Service land and may also be legally required under other statutes and
ordinances. An approved spark arrester is available from your
Coleman® Powermate® product dealer, or may be ordered from
Powermate Corporation, P.O. Box 6001, Kearney, Nebraska 68848.
1-800-445-1805.
Maximum Inlet Pressure . . . . . . . . . . . . . . . . . .Up to 90 PSIG
RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3600 RPM
Temperature of Pumped Fluids . . . . . . . . . . . . . . . .Up to 80°F
Inlet Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3/8” BSP
Discharge Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3/8” BSP
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 lbs.
Crankcase oil Capacity . . . . . . . . . . . . . . . . . . . . . . . .4.7 fl. oz.
Pump oil . . . . . . . . . . . . . . . . . . . . . . .SAE 30W Nondetergent
Consult the factory for special requirements that must be met
if the pump is to operate beyond one or more of the limits
specified above.
Following is information concerning the four nozzles
provided with your pressure washer.
NOTE: The force of the spray on the surface you are
cleaning increases as you move closer to the surface.
0° High Pressure (Red):
The water stream discharged is
very aggressive. Use with extreme caution to prevent damage
to the surface being cleaned or injury to persons or animals.
15° High Pressure (Yellow):
This is the nozzle used for
most cleaning applications. It provides wide coverage and a
powerful water stream.
40° High Pressure (White):
This nozzle is used for
cleaning with a wider coverage over a larger area with a
powerful water stream.
65° Low Pressure (Black):
Provides low pressure spray
and a wide coverage. Used primarily when operating the
chemical injector to apply chemicals.
English
www.powermate.com
The pump will overheat and may be damaged, or cause
damage if allowed to circulate more that five minutes.
SAFETY FEATURES
SPRAY NOZZLE SELECTION
SPECIFICATIONS
