English
6
Congratulations on having purchased a Coemar product. You have assured yourself of a fixture of the highest quality, both in the componentry and
in the technology used. We renew our invitation to you to complete the service information form on the previous page. This will assist in providing
prompt and accurate advice from your Coemar service centre, which you can thoroughly trust and to which you can submit any requests for service
or information. Following the instructions and procedures outlined in this manual will ensure the maximum efficiency of this product for years to
come.
1.Packaging and transportation
1.1 Packaging
Open the packaging and make sure that no part of the equipment has suffered any damage during the transportation. In case of damage to the
fixture, contact your currier and your supplier immediately by telephone, fax or email, and inform them you will formally notify them in writing
through registered letter.
Packing List
Make sure the packaging contains:
1 the
Infinity Spot M
projector.
2 the instruction manual.
3 the Cam
-
Lock support brackets.
1.2 Trasportation
Infinity Spot M
must be transported exclusively in its original packaging or in an appropriate flight case.
2. General information
2.1 Important safety information.
Fire prevention:
1.Infinity Spot M
utilizes a Philips MSR 700 Gold Mini Fast Fit or a Philips MSR Gold 575 MiniFast Fit lamp, the use of any alternative lamp might
be risky and will make the warranty of the fixture null and void.
2.
Never locate the fixture on any flammable surface.
3.
Minimum distance from flammable materials: 0.5m.
4.
Minimum distance from the closest illuminable surface: 0.5m.
5.
Replace any blown or damaged fuses only with identical ones, both in size and value. Refer to the connection diagram if there is any doubt.
6.
Connect the projector to mains power protected by a thermal magnetic circuit breaker.
Preventing electric shock:
1.
Presence of high voltage inside of the fixture. Insulate the projector from mains supply before opening or performing any function which involves
touching the inside of the fixture, including lamp replacement.
2.
For the connection to the mains, adhere strictly to the guidelines outlined in this manual..
3.
The level of technology of
Infinity Spot M
requires the use of specialised personnel for all service applications; refer all work to your authorised
Coemar
service centre.
4.
A good earth connection is essential for the proper functioning of the projector. Never connect the fixture if there is no earth connection.
5.
Mains cables must not come into contact with other cables.
6.
Do not operate the projector with wet hands or in an area where water is present.
7.
The fixture must never be located in an exposed position, or in areas of extreme humidity.
Protection against ultraviolet radiation(UV):
1.
Never turn on the lamp if any of the lenses, filters, or the plastic housing are damaged; their shielding functions will only operate efficiently if they
are in perfect working order.
2.
Never look directly in the direction of the lamp when it is operating.
Safety:
1.
The projector must always be installed with bolts, clamps, or other fixing devices which are suitably rated to support the weight of the projector.
2.
Always use a secondary safety fixing device with chain or steel wire of a suitable rating to sustain the weight of the unit in case of failure of the
principal fixing point.
3.
The external surfaces of the unit, at various points, may reach 150°C. Never handle the unit until at least 10 minutes have elapsed since the lamp
was turned off
4.
Always replace the lamp if any physical damage is evident.
5.
Never install the fixture in an enclosed area lacking sufficient air flow; the room temperature must not exceed 35°C.
6.
Wait at least 10 minutes after the unit has been turned off before attempting to replace or remove the lamp. Always use protection gloves while
replacing the lamp.
7.
The projector contains electronic and electrical components which must under no circumstances be in contact with water, oil or any other liquid.
Failure to do so will compromise the proper functioning of the projector.
Projector movement.
The projector has a pan range of 540° in its base and a tilt range 262° in its yoke; do not obstruct the projector whilst it is moving.
Forced ventilation
On the body of the projector you will note several air vents housing several cooling fans, both in the basis and in the body. To
avoid any problems associated with overheating, never obstruct any of these vents, as this would seriously compromise the proper operation of the
unit.
Protection rating against penetration by external agents:
The fixture is classified as an ordinary apparatus ; its protection grade against penetration by external agents, solid or liquid, is
IP20
.
Содержание Infinity Spot M
Страница 1: ...Infinity Spot M instruction manual manuale di istruzioni Version 2 1 DIS126 ...
Страница 23: ...English 25 ...
