manualshive.com logo in svg

Coemar DR1, Инструкция по эксплуатации

Поделиться
Скачать
Coemar DR1 Скачать руководство пользователя страница 17

EPER

:

EEPROM Error

The EEPROM is either defective or absent; refer to your coemar service centre for a replacement 
component.

DTER

:

DATA Error

The initial parameter settings of the DR1 are either incorrect or corrupt; the DR1 has reloaded its factory
default settings. Turn the unit off and on again. Should the error persist, replace the EEPROM replaced.

FDER

:

EXPLORATION Error 

An error has been identified during the exploration procedure. Repeat the procedure. If the error persists
check the connector plugs and sockets in the dmx universe.

RHER

:

RECEPTION Error

The system is not communicating correctly. Check the connector plugs and sockets in the dmx universe.

IDER

:

PROJECTOR ADDRESS Error

If this error occurs persistently, there is a strong possibility that you have two or more projectors with 
identical IDs. Locate the projectors and alter one or both IDs.

MISS

:

PROJECTOR MISSING Message

The selected projector is not responding. Perform the EXPL (exploration) function to identify all the 
compatible projectors currently installed and operating.

MISM

:

PROJECTOR DIFFERENT Message

You have attempted to perform the REC function on different model projectors. The REC function may 
only be performed on projectors of the same model.

NONE

:

NO PROJECTOR Message

This message will appear when attempting to select projectors after the most recent exploration operation
has indicated no projectors present.

MOVE

:

MOVEMENT AWAITED Message

This message may appear when testing encoders and requires you to move the specific device in order 
allow the testing to occur.

GOOD

:

TEST ENCODER POSITIVE Message

This message may appear when testing encoders to indicate a positive result.

BAD

:

TEST ENCODER NEGATIVE Message

This message may appear when testing encoders to indicate a negative result.

OLD

:

PIN REQUEST Message

This message may appear during the altering PIN operation. and requires you to enter the currently 
valid pin code.

NEW

:

INSERT NEW PIN Message

This message may appear during the altering PIN operation. and requires you to enter the new pin you 
wish to use.

15. Error messages

34

English 

Содержание DR1




















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды