Codinter POWER STICK 200K Скачать руководство пользователя страница 8

Страница: 8 / 14

Singal phase220V Power supply configure of a welder

ITEM

POWER STICK 200K

Air switch

Fuse

Rated current

Knife switch

Cablespecificati

Notice: The melting current of the fuse is two times of its rated current.

Connection between Welder and Electrode Holder (See Output Connection Sketch)

Insert the quick connector of the welding cable on the electrode holder into current output “+”electrode adaptor on

the second half of the front panel and then screw down clockwise.

Connection between Welder and Work Piece (See Output Connection Sketch)

Insert the quick connector of earth cable with earth clamp into current output ‘-’ electrode adaptor on the second

half of the front panel and then screw down clockwise. The earth clamp is connected with work piece.

Notice:

Do not use steel plate or the materials alike which are ill conductor to connect between welder and

work piece.

Singe phase 220V

Cali

Teléfono: (2) 3351214

Carrera 31 A # 10 A - 129
[email protected]

Bogotá

Teléfono: (1) 7433131

Calle 18 # 25 - 41
[email protected]

Medellín

Teléfono: (4) 6053131

Calle 42 B # 64 - 08 Local 21
[email protected]

codinter.com

Содержание POWER STICK 200K















Результаты поиска

Содержание POWER STICK 200K

Отзывы:

Похожие инструкции для POWER STICK 200K

Бренды по названию

Популярные бренды

Codinter POWER STICK 200K, Руководство пользователя

Результаты поиска

Содержание POWER STICK 200K

Отзывы:

Похожие инструкции для POWER STICK 200K

Бренды по названию

Популярные бренды