Code 3 3599L5, Руководство по установке и эксплуатации

Страница: 10 / 16

Hand Held Controller (See Picture on Next Page)
The microphone for talk. 1.
LEV1, when depressed/released once, supplies power to the load connected to Terminal A. This will also shut off the 2.
siren if EU Lock Level 2 or 3, or Auto Siren is enabled. When depressed/released again, cuts power to Terminal A and
shuts off the siren if EU Lock Level 1 is enabled.
LEV2, when depressed/released once, supplies power to the load connected to Terminals A and B. This will also shut 3.
off the siren if EU Lock Level 3 or Auto Siren is enabled. When pressed/released again, cuts power to Terminal B and
shuts off the siren if EU Lock Level 2 is enabled.
LEV3, when depressed/released once, supplies power to the load connected to Terminals A, B, and C. If Auto Siren is 4.
enabled, then SIR1 siren will also turn on. When depressed/released again, cuts power to Terminals A, B, and C, and
shuts off the siren if EU Lock or Auto Siren is enabled.
AUX 1 – Auxiliary, when depressed/released once, supplies power to the load connected to Terminal D. 5.
AUX 2 – Auxiliary, when depressed/released once, supplies power to the load connected to Terminal E. 6.
AUX 3 – Auxiliary, when active, supplies power to the load connected to Terminal F. Active mode is determined by the 7.
mode that AUX 3 is set to. This is set by Dip switch #3.
AUX 4 – Auxiliary, when active, supplies power to the load connected to Terminal G. Active mode is determined by the 8.
mode that AUX 4 is set to. This is set by Dip switch #5.
RAD – When pressed, the radio rebroadcast function over-rides any active siren tone. When the RAD button is re- 9.
leased, the siren will automatically switch back to the siren tone (if any) that was active when the button was pressed.
MAN – When depressed/released once, the siren will produce the Manual tone. This button over-rides any other siren 10.
tone being produced. If EU Lock is enabled, and the minimum Light Level is not currently on, then that Light Level will
also turn on.
AIR – When depressed/released once, the siren will produce the Air Horn tone. This button over-rides any other siren 11.
tone being produced. When the STBY button is depressed/held, the Air Horn button can be depressed/released to
select higher or lower pitch tones. Once the desired tone is chosen, release both buttons.
SIR – When depressed/released, the siren will produce the Wail tone. Continue to depress/release the button to scroll 12.
through the following tones (unless disabled): Wail, Yelp, Hi-Lo, Hyper-Yelp, Hyper-Lo, and Whoop. If EU Lock is en-
abled, and the minimum Light Level is not currently on, then that Light Level will also turn on.
SIR1 – Siren Tone 1, when depressed/released once, the siren will produce the tone preset at the factory (currently 13.
Wail). If EU Lock is enabled, and the minimum Light Level is not currently on, then that Light Level will also turn on. To
change the factory preset, depress and hold the STBY button, and then depress/release the SIR1 button to go to the
next available tone. Once the desired tone is chosen, release both buttons.
SIR2 – Siren Tone 2, when depressed/released once, the siren will produce the tone preset at the factory (currently 14.
Yelp). If EU Lock is enabled, and the minimum Light Level is not currently on, then that Light Level will also turn on. To
change the factory preset, depress and hold the STBY button, and then depress/release the SIR2 button to go to the
next available tone. Once the desired tone is chosen, release both buttons.
STBY – When depressed/released, any active siren tone is shut off. When depressed/held for 5 or more seconds with- 15.
out any other button press, keypad lighting will shut off. Depress/hold again for 5 or more seconds without any other
button press to turn keypad lighting back on. In addition this button is used to change the siren presets as described
above.
PTT (Push To Talk) – The PA portion of the siren is activated each time the Microphone PTT button is pressed. When 16.
pressed, the PA function over-rides any active siren tone and routes the PA audio through the siren speaker. When the
PTT button is released, the siren will automatically switch back to the siren tone (if any) that was active when the button
was pressed.
Volume Control - Adjusting this wheel upwards increases volume, and downwards decreases volume. 17.
10