background image

- 17 - 

12. TROUBLESHOOTING 
 

PROBLEM 

PROBABLE CAUSE

 

CORRECTIVE ACTION

 

Engine does not 

start. 

Throttle choke not in the correct position 

for the prevailing conditions. 

Move throttle choke to the correct position 

Fuel tank is empty. 

Fill the tank with fuel: refer to the ENGINE MANUAL. 

Air filter element is dirty. 

Clean air filter element: refer to the ENGINE MANUAL 

Spark plug loose. 

Tighten spark plug to 25-30Nm. 

Spark plug wire loose or 

disconnected from plug. 

Install spark plug wire on spark plug. 

Spark plug gap is incorrect. 

Set gap between electrodes at 0.7 to 0.8mm 

Spark plug is defective 

Install new, correctly gapped plug: refer to the ENGINE 

OWNERS MANUAL 

Carburetor is flooded with fuel 

Remove air filter element and pull starter rope 

continuously until the carburetor clears itself and then 

install the air filter element. 

Faulty ignition module 

Contact the service agent. 

Engine difficult to 

start or loses 

power. 

Dirt, water, or stale fuel tank. 

Drain fuel and clean tank. Fill tank with clean, fresh fuel 

Vent hole in fuel tank cap is plugged. 

Clean or replace fuel tank cap. 

Air filter element is dirty. 

Clean air filter element. 

Engine operates 

erratically. 

Spark plug is defective. 

Install new, correctly gapped plug: refer to the ENGINE 

OWNERS MANUAL 

Spark plug gap is incorrect. 

Set gap between electrodes at 0.7 to 0.8mm 

Air filter element is dirty. 

Clean air filter element: refer to the ENGINE OWNERS 

MANUAL 

Engine idles 

poorly. 

Air fliter element is dirty. 

Clean air filter element: refer to the ENGINE OWNERS 

MANUAL 

Air slots in engine shroud are blocked. 

Remove debris from slots. 

Cooling fins and air passages under 

engine blower housing are blocked. 

Remove debris from cooling fins and air passages. 

Engine skips at 

high speed. 

Gap between electrodes of spark plug are 

too close. 

Set gap between electrodes at 0.7 to 0.8mm 

Engine overheats 

Cooling air flow is restricted. 

Remove any debris from slots in shroud, blower housing, 

and air passages 

Incorrect spark plug. 

Install RJ19LM spark plug and cooling fins on engine 

Mower vibrates 

abnormally 

Cutting assembly is loose. 

Tighten blade 

Cutting assembly is unbalanced 

Balance or replace the blade 

 
 
 

 

 

 

Содержание MX564SPB




















Отзывы: