background image

Customer Assistance

Warranty

Introduction

19

Operation

18

Mode Functions

Operation

Privacy Code Scan

Your microTALK radio can automatically scan the

Privacy

Codes

(either CTCSS 01 through 38 or DCS 01 through 104)

within one channel. Only one set of privacy codes (CTCSS
or DCS) can be scanned at a time.

To scan privacy codes:
1.

While in

Standby

mode, press the

Channel Up

or

Channel Down

button

to choose the channel on which you
wish to scan privacy codes.

2.

Press the

Mode

button until either the CTCSS

or the DCS icon appears on the display and
the

Scan

icon and the privacy code numbers

flash on the display.

3.

Press the

Channel Up

or

Channel Down

button to begin scanning privacy codes
within the channel you selected.

The

Scan

icon will continue to be displayed

when privacy code scan is

on

. Your radio will

continue to scan privacy codes and stop as an
incoming transmission is detected. Your radio
will remain on that channel/privacy code for
10 seconds.

While setting privacy code scan, if you do not
press any buttons for 15 seconds, your radio
will automatically return to

Standby

mode on

the channel/privacy code that was displayed
before you entered mode functions.

During channel scan (while receiving an incoming transmission),
you can choose from the following:

a.

Press and hold the

Talk

button to communicate on

that channel. Your radio will remain on that channel
and return to

Standby

mode.

b.

Press the

Channel Up

or

Channel Down

button to

resume scanning channels.

If you press the

Talk

button while scanning, but more than

10 seconds after receiving a transmission, you will transmit
on the channel on which you last received a transmission.
This will return the radio to

Standby

mode.

If you do not press any button within 10 seconds after
receiving a scanned transmission, your radio will automatically
resume scanning channels.

During channel scan (while not receiving a transmission),
you can choose from the following:

a.

Press and hold the

Talk

button to communicate on the

channel or channel/privacy code that was displayed before
you entered mode functions or the channel on which, during
scanning, you last received a transmission. This will then
return the radio to

Standby

mode.

b.

Press the

Mode

button to proceed to set privacy

code scan on the channel that was either displayed before
you entered mode functions or on which, during channel
scanning, you last received a transmission (see page 19
for further details).

c.

Press the

Lock/Enter

button to return to

Standby

mode

on the channel/privacy code that was displayed before you
entered mode functions or the channel on which, during
scanning, you last received a transmission.

Mode Button

Channel Buttons

Select Channel

Scan Privacy Codes

Nothing

Comes Close to a Cobra

®

Содержание microTALK CXR750


















Отзывы: