background image

Customer Assistance

Warranty

Introduction

21

Operation

20

Operation

Memory Location Scan

Your microTALK radio can automatically scan up to
10 programmed

Memory Locations

.

If there are one or fewer memory locations
programmed in your radio, the scan memory
locations option will not be available. To program
at least two memory locations, see program
memory locations on page 13.

To scan memory locations:
1.

Press the

Mode

button until the

Scan

icon,

Memory

icon and the memory location

number flash on the display.

2.

Press the

Channel Up

or

Channel Down

button to begin scanning memory locations.

The

Scan

icon and the

Memory

icon will

continue to be displayed when memory
location scan is

on

. Your radio will continue

to scan memory locations and stop if an
incoming transmission is detected. Your
radio will remain on that memory location
for 10 seconds.

While setting memory location scan, if you
do not press any buttons for 15 seconds,
your radio will automatically return to

Standby

mode on the channel/privacy code

displayed before you entered mode functions.

During privacy code scan (while receiving an incoming
transmission), you can choose from the following:

a.

Press and hold the

Talk

button to communicate on

that channel/privacy code. Your radio will remain on
that channel/privacy code and return to

Standby

mode.

b.

Press the

Channel Up

or

Channel Down

button to

resume scanning privacy codes.

If you press the

Talk

button while scanning, but more than

10 seconds after receiving a transmission, you will transmit
on the channel/privacy code on which you last received a
transmission. This will then return the radio to

Standby

mode.

If you do not press any button within 10 seconds, your
radio will automatically resume scanning privacy codes.

During privacy code scan (while not receiving a transmission),
you can choose from the following:

a.

Press and hold the

Talk

button to communicate on

the channel/privacy code that was displayed before you
entered mode functions or the channel/privacy code on
which, during scanning, you last received a transmission.
This will return the radio to

Standby

mode.

b.

Press the

Mode

button to proceed to set memory location

scan (see page 21 for further details).

c.

Press the

Lock/Enter

button to return to

Standby

mode on the channel/privacy code that was displayed
before you entered mode functions or the channel/
privacy code on which, during scanning, you last
received a transmission.

Mode Functions

Mode Button

Channel Buttons

Scanning Locations

Nothing

Comes Close to a Cobra

®

Содержание microTALK CXR750


















Отзывы: