manualshive.com logo in svg

Cobra CB6, Руководство по обслуживанию, Страница: 28 / 34

Поделиться
Скачать
Cobra CB6 Скачать руководство пользователя страница 28

24 

A 

Appendix A:  Gas Type Conversion 

Revision 2 

© 

Moffat Ltd, August 2012 

Cobra Series Gas Barbeque 

Conversion Procedure 

NOTE: 



These conversions should only be carried out by qualified persons.  All connections must 
be checked for leaks before re-commissioning appliance. 



Adjustment of components that have adjustments/settings sealed (e.g. paint sealed) can 
only be adjusted in accordance with the following instructions and shall be re-sealed  
before re-commissioning this appliance. 



For all relevant gas specifications refer to the table at the end of this section. 

 

Main Burners 
 

1. 

Remove the gas control knobs from the front control pan-
el.  The control knobs are a push fit onto the shaft of the 

gas control valves. 

 

 
 

 

 

2. 

Remove the front control panel by slackening the 2 

screws on the front lower edges of the control panel and 
remove the panel from the front of the barbeque. 

 

 

 
 

 

 

 

3. 

Remove the barbeque grates and inner radiants to reveal the main 

burners. 

 

 

4. 

Carefully push the main burners forward and negotiate between the 

shield brackets fitted over the end of the burners and remove the 
burners from the barbeque to reveal the main burner injectors. 

 

 

 
 

 

5. 

Unscrew the main burner injectors from the barbeque using a 

13mm / 

1

/

2

" A/F spanner. 

6. 

Determine the correct injector sizes for the corresponding gas, from 

the rating plate located behind the main control panel, next to the 

manifold test point. 

7. 

Replace with the correct size injectors. 

8. 

Refit the main burners, castings, inner radiants and grates to the 

barbeque. 

C

AUTION

: 

 

Ensure that the Unit is isolated from the gas supply before commencing  
servicing. 

Main Burner 

Gas Control Valves 

Piezo Igniters 

2 Screws 

Gas Control Knobs 

Main Burner 

Injector 

Figure A.1. 

Figure A.2. 

Figure A.3. 

Figure A.4. 

Содержание CB6



































Отзывы:

Нет отзывов