Cobra CB6 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 34

Cobra CB6 Скачать руководство пользователя страница 21

6

Service Procedures

17

Revision 2

©

Moffat Ltd, August 2012

Cobra Series Gas Barbeque

1) Remove the control panel (refer 6.1.1).
2) Remove 2 screws holding shaft plate to gas

control body and remove control shaft and

plate. Note orientation of shaft for correct

re-assembly.

6.3.1 Gas Control Valve Re-Greasing

6.3 Adjustment / Calibration

Figure 6.3.1a

Figure 6.3.1b

Spindle

Two Screws

3) Using needle nose pliers or similar, pull out gas

control spindle, again noting its orientation.

4) Apply a suitable high temperature gas cock

grease or lubricant such as ROCOL - A.S.P (Anti

scuffing paste) / Dry Moly Paste to the outside
of the spindle.

5) Replace the spindle and re-assemble gas

control in reverse order.

6.3.2 Low Fire Rate Adjustment

1) Remove the control panel (refer 6.1.1).
2) Light barbecue and set gas control to low

position.

3) Remove gas control knob, and using a small

flathead screwdriver, adjust the low fire screw

until the desired flame setting is achieved.

Figure 6.3.2

Low Fire

Adjustment Screw

«
...
19
20
21
22
23
...
»

Содержание CB6



































Отзывы:

Нет отзывов