manualshive.com logo in svg

COBHAM Sea Tel 4010W-33, Руководство по установке

Поделиться
Скачать
COBHAM Sea Tel 4010W-33 Скачать руководство пользователя страница 50

4010W-33 Installation Manual 

Setup – Targeting 

 

8-2 

8.3.

 

EL TRIM 

Elevation trim offset parameter is entered in tenths of degrees.  Adjusts display to correct for antenna alignment errors 

or imbalances in the antenna system.  Increase number to increase display.  Refer to “Optimizing Targeting” in the 
Setup section of your antenna manual.   
To update:  While in the EL TRIM sub-menu, press the LEFT arrow key to bring the cursor under the ones digit.  Press 

the UP or DOWN arrow key to increment or decrement the selected digit.  Minus values are entered by decrementing 

below zero.  Use the LEFT or RIGHT arrow key to move the cursor left or right to select other characters to modify.  

When you are finished modifying press ENTER to execute the new value OR press NEXT to abort and exit setup mode. 
Continue with Azimuth trim, then re-target the satellite several times to verify that targeting is now driving the 
antenna to a position that is /- 1.0 degrees of where the satellite signal is located. 

8.4.

 

AZ TRIM 

Azimuth trim offset parameter is entered in tenths of degrees.  Offsets true azimuth angle display to compensate for 
installation alignment errors when used with Ships Gyro Compass input reference. 

 Azimuth Trim does not affect 

REL azimuth reading

.  Increase number to increase displayed value. Refer to “Optimizing Targeting” in the Setup 

section of your antenna manual.   
To update:  While in the AZ TRIM sub-menu, press the LEFT arrow key to bring the cursor under the ones digit.  Press 

the UP or DOWN arrow key to increment or decrement the selected digit.  Minus values are entered by decrementing 
below zero.  Use the LEFT or RIGHT arrow key to move the cursor left or right to select other characters to modify.  

When you are finished modifying press ENTER to execute the new value OR press NEXT to abort and exit setup mode. 
Then re-target the satellite several times to verify that targeting is now driving the antenna to a position that is within 

+/- 1.0 degrees of where the satellite signal is located. 

 
 

Содержание Sea Tel 4010W-33














































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды