Coastal Amusements Jacks Hi Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 28

background image

Page 17

5

Lighting

5.1

Cabinet Lighting

Fluorescent Lighting

WARNING - Dangerous Voltages (230v) - switch OFF prior to replacing!

Fluorescent tube lighting is situated in both the top sign and the coin entry areas. The lighting in the
coin entry area has double insulated fittings in accordance with current regulations, and the control
gear is mounted on a light tray in each top sign, together with the control gear for that top sign
lighting.

Light Tray Located In Top Sign

Dichroic Lighting

WARNING - These lamps become very hot in operation

allow to cool before handling!

Low voltage dichroic spot lamp lighting is situated at the top of each playfield. These lamps are
easily replaced by simply pulling the old bulb free from the fitting, and pushing the replacement
bulb back in place. Power for these lights is derived from an isolation transformer (see power
supplies section of this manual).

Beacon Light

Located on the top of each top sign, these red beacon lights serve to enhance the game by flashing in
the event of a bonus win and serve to draw the operating staffs attention in the event of a problem
by remaining on permanently.

«
...
15
16
17
18
19
...
»

Содержание Jacks Hi





























Отзывы:

Нет отзывов

Похожие инструкции для Jacks Hi

Бренд: Seaga Страницы: 13

FORMULA GP1 CHRONO

Бренд: falgas Страницы: 25

Бренд: N&W Global Vending Страницы: 72

Бренд: Horizon Fitness Страницы: 34

Бренд: Coast to Coast Страницы: 20

Harmony Upright

Бренд: Atronic Страницы: 51

Бренд: NAMCO Страницы: 29

Бренд: Bally Страницы: 90

Бренд: Electrolux Страницы: 40

Бренд: Bandai Namco Страницы: 194

Бренд: Williams Electronics Страницы: 38

Бренд: Konami Страницы: 20

Бренд: Konami Страницы: 22

Nagano Winter Olympics '98

Бренд: Konami Страницы: 22

Racing Jam Chapter II

Бренд: Konami Страницы: 31

Lethal Enforcers II Gun Fighters

Бренд: Konami Страницы: 29

Бренд: Konami Страницы: 47

Бренд: Konami Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды