manualshive.com logo in svg

CML Microcircuits PE0403, Руководство пользователя

Поделиться
Скачать
CML Microcircuits PE0403 Скачать руководство пользователя страница 7

Evaluation Kit for CMX724x/CMX734x 

 

PE0403 

 

 

 2014 CML Microsystems Plc 

7 

um0403/1 

 

3. 

Quick Start 

This section is divided into two sub-sections. The first is for those users who are using the PE0403 with a 
PE0002  controller  card  and  its  Windows  PC  GUI  software.  The  second  is  for  users  who  are  using  the 
PE0403 by itself, without a PE0002. 
 

3.1. 

With PE0002 

Note  that  the  C-BUS  connector,  J7,  and  the  power  connector  J18  are  both  right  angle  headers  and  are 
designed to plug directly into sockets J5 (C-BUS 1 port) and J9 respectively, or sockets J3 (C-BUS 2 port) 
and J7 respectively, of a PE0002. 
 

3.1.1.  Setting-Up 

Refer  to the  PE0002  user manual and follow the instructions given in the quick start section. Ensure the 
jumpers on J2 are open circuit. The CMX7240/CMX7340 BOOTEN1 and BOOTEN2 pins are driven from 
the PE0002. 
 
The basic arrangement, when used with the PE0002, is shown below: 
 

PE0002

PC

USB Cable

PE0403

J18

J2

J3 or J5

C-BUS

Direct Connections

J2

J8

J9 or J7

+V

J7

Power
Supply

 

Figure 2  PE0403 used with PE0002 

 

3.1.2.  Operation 

The Function Image

TM 

(FI) must now be loaded into the CMX7240/CMX7340 device. A FI is provided as a 

‘C’  type  header  file  and  must  be  obtained  from  the  CML  Project  Resource  Portal.  This  can  be  loaded 
directly from a file on the PE0002 host PC to the CMX7240/CMX7340. 

 
The PE0403 should now be ready for evaluation of the CMX7240/CMX7340 with the chosen FI. 
 

Содержание PE0403




























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды