CML Microcircuits PE0403 Скачать руководство пользователя страница 13

Страница: 13 / 27

Evaluation Kit for CMX724x/CMX734x

PE0403



2014 CML Microsystems Plc

um0403/1

Table 3 Jumpers

JUMPERS

Link

Ref.

Positions

Default

Position

Description

JP2

1-2

Short

Isolates digital supply rail from CMX7240/CMX7340.

JP3

1-2

Short

Isolates analogue supply rail from CMX7240/CMX7340.

JP4

1-2

Open

Connects Audio(J1) connector Ring to Tip.

JP6

1-2

Short

Select Mic or Line level for Mic input (Short for Mic level)

1-2

Open

Manual BootEn1 control (short = LO).

3-4

Open

Manual BootEn2 control (short = LO).

1-2

Open

Crystal clock source

– if components fitted by customer.

3-4

Open

Crystal clock source

– if components fitted by customer.

5-6

Short

19.2MHz oscillator clock source.

7-8

Open

External clock source.

9-10

Short

Ground external clock input.

1-2

Short

Isolates channel 1(DISC) input +ve from instrumentation
interface.

3-4

Short

Isolates channel 1(DISC) input -ve from instrumentation
interface.

7-8

Short

Isolates channel 2(ALT) input -ve from instrumentation
interface.

9-10

Short

Isolates channel 2(ALT) input +ve from instrumentation
interface.

J13

1-2/2-3

1-2

Connect the 50 Ohm driver to J14 if (1-2), or bypass the
50 Ohm driver if (2-3)

J12

1-2/2-3

Open

Set Mic bias level, 1-2 for 3V3, 2-3 for +V input, or open for
bias disabled. See 6.1.6.

J15

3-4,5-6,7-9

See 6.1.6 Audio Interfaces.

11-12

Open

Select coupling on Mic input. Short to DC couple.

J16

1-2

1-2/2-3

Connect the 50 Ohm driver to J17 if (1-2) or bypass the
50 Ohm driver if (2-3)

Содержание PE0403




























Результаты поиска

Содержание PE0403

Отзывы:

Бренды по названию

Популярные бренды

CML Microcircuits PE0403, Руководство пользователя

Результаты поиска

Содержание PE0403

Отзывы:

Бренды по названию

Популярные бренды