Cloud CDI-46 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 28

Cloud CDI-46 Скачать руководство пользователя страница 18

CDI-46 Installation and Setup Guide V1.3

18

Firmware update

Download the CDI-46 firmware update from

www.cloud.co.uk

.

1.

Read the update notes to check that the update is applicable to your unit.

2.

Establish the Ethernet connection between the CDI-46 and your network switch. Launch your usual web browser and

connect to the CDI-46 in the usual way.

3.

Log in using the Installer PIN.

4. Click

Menu

>

Config

>

Device Info

.

5.

Click

Upload

.

6.

Enter the Installer PIN again.

7.

The CDI-46 will now enter

bootloader mode

.

8.

Close the browser page.

9.

Run the Firmware Update application on a Windows® PC connected to the same network.

10. Click

Discover

.

11.

Click the IP Address listed in

BOLD

font.

12.

Check and confirm which settings you would like to overwrite on the

Update

interface.

13. Click

Update

.

14.

Wait for the “

Firmware updated successfully” message.

15.

Click

OK

, then close the Firmware Update application

Change Installer PIN

Click the

Change PIN

tab to open the

Reset your PIN

page.

This page lets you change the Installer PIN. You will need to confirm the current PIN in the

Enter your current PIN

field before proceeding to enter a new one in both the

Add a new PIN

and the

Confirm your new PIN

fields, and Click

the

Update

button.

«
...
16
17
18
19
20
...
»

Содержание CDI-46





























Отзывы:

Нет отзывов