Climax CH-MG Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 37

Climax CH-MG Скачать руководство пользователя страница 17

14

Group 1 > Group 3 > Wait 5 minutes > Group 1 > Group 3 >
Wait 5 minutes > Group 1 > Group 3 > Stops reporting



Status Events

:

CH-MG will only go through one reporting cycle for Status reports.

For example, if Groups 1 and 3 are programmed for “Status” reports:

Group 1 > Group 3 > Stops reporting whether Groups 1 and 3
succeeded or not

SMS Report text format



Below are the SMS Text messages sent to user according to the condition
of the CH-MG.

SMS text table:

CH-MG Condition

SMS Text format

Low battery status

CH-MG Low Battery

Battery voltage restored

CH-MG Battery Restored

Wakes up time

CH-MG Periodic Test

Weak Signal strength from the Local

Base Station

CH-MG Weak Signal Strength

AC Power disconnected

CH-MG Power Failure

AC Power connected

CH-MG Power Restored



When help is sent by pressing the CH-MG’s Help Button, in which
according to CID event code, the user will receive SMS text format as
follows:

CH-MG Medical Help

«
...
15
16
17
18
19
...
»

Содержание CH-MG






































Отзывы:

Нет отзывов