Clifford Model RSX3.5, Руководство по установке

Страница: 48 / 60

4 48 8
© 2005 Directed Electronics—all rights reserved
2 2--9 9 FFA ACCTTO OR RY Y A ALLA AR RM M D DIISSA AR RM M W WIITTH H CCH HA AN NN NEELL 2 2:: In the default setting the factory alarm disarm output will disarm
the factory alarm system any time the button(s) controlling Channel Two is pressed.
2 2--1 10 0 FFA ACCTTO OR RY Y A ALLA AR RM M D DIISSA AR RM M— —W WIITTH H U UN NLLO OCCK K,, BEFORE UNLOCK, REMOTE START ONLY:: In the default setting the
factory alarm disarm output will disarm the factory alarm system any time the button(s) controlling Unlock is pressed.
The “Before Unlock” output to disarms the factory alarm before the unlock output activates and before remote start
is activated. The “Remote Start Only” output disarms the factory alarm only before the remote start is activated.
2 2--1 11 1 FFA ACCTTO OR RY Y A ALLA AR RM M D DIISSA AR RM M P PU ULLSSEESS— —SSIIN NG GLLEE,, DOUBLE:: Selectable for a single or double-pulse for the vehicle’s
factory alarm disarm input requirements.
2 2--1 12 2 CCH HA AN NN NEELL 4 4 V VA ALLIID DIITTY Y//LATCHED//LATCHED RESET WITH IGNITION//30 SECOND TIMED O OU UTTP PU UTT:: This wire pro-
vides a (-) 200mA output whenever the transmitter button(s) controlling Channel 4 is pressed. This output can
be programmed to provide the following types of outputs (see also the Feature Menus section):
■
V Vaalliid diittyy:: Output that will send a signal as long as the transmission is received.
■
LLaattcch heed d:: Output that will send a signal when the Channel 4 button(s) is pressed and will continue until the
same button(s) is pressed again.
■
LLaattcch heed d,, rreesseett w wiitth h iig gn niittiio on n:: Similar to the latched output, this type of output turns on the first time the
Channel 4 button(s) is pressed and turns off the next time the same button is pressed. This type of output
additionally stops and resets whenever the ignition is turned on and then off.
■
3 30 0--sseecco on nd d ttiim meed d:: Output that will send a continuous signal for 30 seconds.
N No ottee:: All auxilary channel timed outputs can be programmed using the Bitwriter® (1-90
seconds).
2 2--1 13 3 CCH HA AN NN NEELL 4 4 LLIIN NK KIIN NG G ((N NO ON NEE))//ARM, DISARM, REMOTE START:: When programming to validity or timed output
this can be programmed to activate when arming or disarming (or remote start) with the transmitter.
2 2--1 14 4 CCH HA AN NN NEELL 5 5 V VA ALLIID DIITTY Y//LATCHED//LATCHED RESET WITH IGNITION//30 SECOND TIMED O OU UTTP PU UTT:: Channel Five can
be programmed for these output configurations. The unit is set to the default validity output. To change the con-
figuration, use the two-chirp setting to toggle through the different configurations. Refer to feature 2-10 for
additional detail.
2 2--1 15 5 CCH HA AN NN NEELL 5 5 LLIIN NK KIIN NG G ((N NO ON NEE))//ARM, DISARM, REMOTE START:: Refer to feature 2-13 for additional detail.
2 2--1 16 6 CCH HA AN NN NEELL 6 6 V VA ALLIID DIITTY Y//LATCHED//LATCHED RESET WITH IGNITION//30 SECOND TIMED O OU UTTP PU UTT:: Channel Five can
be programmed for these output configurations. The unit is set to the default validity output. To change the con-
figuration, use the two-chirp setting to toggle through the different configurations. Refer to feature 2-10 for
additional detail.
2 2--1 17 7 CCH HA AN NN NEELL 6 6 LLIIN NK KIIN NG G ((N NO ON NEE))//ARM, DISARM, REMOTE START:: Refer to feature 2-13 for additional detail.