background image

6. The ACE 7500 can also provide double

pulses (+ or -) for lock and/or (+ or -)

unlock that is required by some vehicles

(such as some Nissans, VWs, and Audis).   

Wire the door locks following the steps

above and select the 2x lock and/or

unlock feature in installer-programming.

  Park ing Lights  

The ACE 7500 has built-in parking light

relays. To determine whether the vehicle has 

single or dual parking light circuit(s), you

must access the fuse panel.  A single circuit

has one fuse; a dual circuit has two.

Sin gle Park ing Light Cir cuit (Most

Japa nese and Ameri can Ve hi cles)

1. Turn on the parking lights and access the 

Parking Light wiring in one of the

following locations:

n

Near the head light switch

n

In the door sill har ness go ing to the

rear lights

n

At any of the four Park ing Light bulbs

2. If working underdash, be sure to turn the

dashlight dimmer to its lowest setting.

3. Connect a voltmeter lead to ground and

find the single wire that shows +12v

when the parking lights are on and 0

volts when they are off.

4. Connect 

both

 of the BROWN wires to

the parking light wires.

5. Connect the RED 18AWG wire from the 

12-pin connector to the vehicle battery

positive (+) terminal via the supplied

20-amp fuse and fuseholder.

Dual Park ing Light Cir cuit (Most

Euro pean Ve hi cles)

1. Turn on the parking lights and access the Parking Light wiring in one of the following

locations:

n

Near the head light switch

n

In the door sill har ness go ing to the rear lights

n

At any of the four Park ing Light bulbs

2. If working underdash, be sure to turn the dashlight dimmer to its lowest setting.

3. Connect a voltmeter lead to ground and find the two wires that show +12v when the

parking lights are on and 0 volts when they are off.

4. Connect one lead to the left-side Parking Light circuit and connect the other lead to the

right side circuit.

5. Connect the RED 18AWG  wire from the 12-pin connector to the vehicle battery positive 

(+) terminal via the supplied 20-amp fuse and fuseholder.

NOTE: Never con nect the RED 18AWG wire to ground. Al ways pick up the

positive- switching park ing light line(s).

9

Содержание ACE 7500

























Отзывы: