background image

B/Problem:

 Skillet heats too slowly or not hot enough. (Note: Maximum surface temp. is 425°F). 

Possible Causes

 

 
 

 
 

1. Low incoming gas pressure.

 

 
 

2. Detective or incorrectly adjusted gas control valve.

 

 

3. Detective or incorrectly adjusted control thermostat.

 

 

4. Detective or incorrectly adjusted safety thermostat.

 

 
 

Fault Isolation Procedure

 

 

 

Step

 

Test

 

Result

 

Remedy

 

1.

 

Yes

 

Go to step # 3.

 

 
 

Tilt skillet fully forward and manually activate the tilt 
safety switch. Inspect the burner flame for a period of 
4 or 5 minutes, Is the burner flame strong and 
constant?

 

No

 

Go to step # 2.

 

2.

 

There is an operating gas supply problem. either 
incoming or outgoing. Refer to Pilot Flame 
Adjustment and Gas Pressure Adjustment Procedure. 
If this does not correct the problem, check incoming 
operating gas supply. It should be minimum 7" WC 
natural gas or 12" WC LP gas. If gas pressure is 
correct, replace defective gas control valve.

 

 
 

 
 

3.

 

Yes

 

Go to step # 4.

 

 
 

In an operating situation and with control thermostat 
set at #10, does the operating (upper) pilot light go 
out too early? (Burners shut off too early)

 

No

 

Go to step # 2.

 

4.

 

Yes

 

Adjust or replace safety thermostat (adjust to 470°F)

 

 
 

Immediately after operating (upper) pilot goes out, 
turn control thermostat to #1. Can you hear or feel the 
thermostat "clicking" off?

 

No

 

Adjust or replace control thermostat (adjust to approx. 
425°F)

 

 

C/Problem:

 Skillet is overheating. 

Replace or adjust control thermostat (adjust to approx. 425°F) Verify that the safety thermostat shuts off 
at approx. 470°F. 
 
 
 
 
 
 
 
 

17 

Содержание SGL-X

























Отзывы:

Похожие инструкции для SGL-X