CMS-1 CARBON MONOXIDE MONITOR
Page 1
© 2017 CLEMCO INDUSTRIES CORP.
www.clemcoindustries.com
Manual No. 23301, Rev. F
1.0
INTRODUCTION
1.1
Scope of manual
1.1.1
These instructions cover the setup, operation,
maintenance, troubleshooting, and replacement parts for
the CMS-1 carbon monoxide (CO) monitor.
1.1.2
The CMS-1 monitor is manufactured by
Invertech Inc., for Clemco Industries Corp. The monitor
is a potential life saving instrument. To assure its
performance, the monitor must be properly installed,
tested, calibrated, and maintained. Before installing and
using the monitor, all personnel involved with the
operation and maintenance of the instrument must read
this entire manual, including the orange cover.
1.2
Safety Alerts
1.2.1
Clemco uses safety alert signal words, based on
ANSI Z535.4-2011, to alert the user of a potentially
hazardous situation that may be encountered while
operating this equipment. ANSI's definitions of the signal
words are as follows:
This is the safety alert symbol. It is
used to alert you to potential physical
injury hazards. Obey all safety
messages that follow this symbol to
avoid possible injury or death.
Notice indicates information that is considered
important, but not hazard-related, if not
avoided, could result in property damage.
Caution indicates a hazardous situation that, if
not avoided, could result in minor or moderate
injury.
Warning indicates a hazardous situation that, if
not avoided, could result in death or serious
injury.
Danger indicates a hazardous situation that, if
not avoided, will result in death or serious
injury.
1.3
Table of Contents
SUBJECT
SECTION LOCATION
INTRODUCTION ........................................................ 1.0
Scope of Manual ......................................................... 1.1
Safety Alerts ............................................................... 1.2
Components ............................................................... 1.4
Operating Principles ................................................... 1.5
Annunciator Lights and Alarms, Use and Functions ... 1.6
Digital Display Window ................................................ 1.7
Switches, Use and Functions ..................................... 1.8
Optional Accessories .................................................. 1.9
Remote alarm ........................................................... 1.9.1
SETUP ........................................................................ 2.0
Assembling the Monitor .............................................. 2.1
Mounting the Monitor................................................... 2.2
Compressed-Air Connections .................................... 2.3
Air pressure requirements .................................... 2.3.1
Connecting to respirator air supply ...................... 2.3.2
Electrical Connections ................................................ 2.4
120-Volt AC supply ................................................ 2.4.1
AC to 12-Volt DC field conversion ........................ 2.4.2
Changing Alarm Trip-Point ......................................... 2.5
Connecting an External Alarm and Shutdown device ... 2.6
OPERATION .............................................................. 3.0
Setup for Operation .................................................... 3.1
Warm-Up Period ......................................................... 3.2
Operating Mode .......................................................... 3.3
Shutdown .................................................................... 3.4
CALIBRATION TEST and CALIBRATION ............... 4.0
Difference Between Calibration Test and Calibration .... 4.1
Calibration test ..................................................... 4.1.2
Calibration process ................................................ 4.1.3
Stabilization Period...................................................... 4.2
Prepare Calibration Connector ................................... 4.3
Prepare Monitor for Calibration ................................... 4.4
Calibration Test .......................................................... 4.5
Calibration ................................................................... 4.6
Return Monitor to Operating Mode ............................. 4.7
Impurity-Free Air (zero contamination) Test ............... 4.8
ZEROING the MONITOR ........................................... 5.0
GENERAL MAINTENANCE ...................................... 6.0
Cleaning ...................................................................... 6.1
Calibration Test Schedule .......................................... 6.2
Calibration Schedule .................................................. 6.3
Alarm Test .................................................................. 6.4
