manualshive.com logo in svg

ClearSpan PB03020R4, Инструкция по эксплуатации

Поделиться
Скачать
ClearSpan PB03020R4 Скачать руководство пользователя страница 19

19

CLEARSPAN

™

 GARAGES

Revision date: 09.14.10

INSTALL MAIN COVER

Gather the parts:
•  1.315" x 75" swaged pipe (131S075)
•  1.315" x XX" plain pipe (131P0XX)
•  Main cover 
•  Tek screws 

The cover conduit assemblies consists of 1.315'' x 75'' 

(#131S075) swaged pipes (number is determined by 

shelter length) and one (1) 1.315'' x XX'' (#131P0XX) plain 

pipe. 

 

The XX'' represents the remaining length needed to reach 

the end of the frame. Consult the Spec Sheet for part 

identification and the Side Profile diagrams in the Quick 

Start section for your building. 

 

Assembly Procedure  

 

NOTE: 

When handling the main cover and setting it in 

position, do not pull on the end straps. They will pull out of 

the cover.

WARNING: 

To prevent damage to the cover and to 

prevent serious personal injury, DO NOT attempt to 

install the main cover on windy days.

1.  Assemble two main cover conduits. Start each conduit 

assembly with one plain pipe and add swaged pipes to 

arrive at the correct length.  

 

a.  Locate all sections of pipe needed to assemble 

the cover conduit.

b.  Insert the swaged end of each pipe into the 

plain end of another pipe until the conduit is 

assembled.

c.  Secure each pipe joint with a Tek screw.

NOTE:

 Use duct tape to tape the Tek screws to 

prevent damage to main cover. 

2.  After assembling the cover conduits, locate the main 

cover and unfold it on a clean, smooth surface near the 

frame.  

 

NOTE:

 When handling the cover and setting it in  

position, do not pull on the end straps. They will pull out  

of the cover. Unfold the cover with the inside surface 

facing up.

3.  Locate the cover end straps and align these with the 

front and back of the shelter.

4.  Insert the cover conduits into pockets of the cover. 

  

NOTE:

 Shelter shown above may differ in length from 

the actual model. 

5.  To pull the cover over the frame, attach ropes to both 

ends of the cover conduit farthest from the frame. Wrap 

the rope around the conduit a few times to prevent it 

from slipping off. 

Cover Conduits

Cover 

Ends w/

Strapping

Main Cover Pocket

Main Cover Pocket

NOTE:

 Depending on the length of the cover it may 

be necessary to attach additional ropes to the cover 

conduit between the end ropes by cutting a small 

opening in the cover pocket and tying the rope around 

the conduit. DO NOT cut through the cover. 

Cut 

through the conduit pocket only.

6.  With all ropes attached to the cover conduit, lift the 

conduit and carry the cover toward the base of the 

frame.

Содержание PB03020R4






























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды