manualshive.com logo in svg

ClearSpan PB03020R4, Инструкция по эксплуатации

Поделиться
Скачать
ClearSpan PB03020R4 Скачать руководство пользователя страница 11

11

CLEARSPAN

™

 GARAGES

Revision date: 09.14.10

RAFTER ASSEMBLY (continued)

10. After attaching all center bracing components, position 

the brace assembly between the rafter legs and at the 

top of the rafter.

11.  Align the 105086 bracket with the center of the rafter 

(top) and secure the bracket using Tek screws.

The diagram below shows the assembled center 

bracing for the rafter.

 

12. Locate the four (4) connection plates (#105087) and 

attach two (2) plates to the horizontal center brace tube 

and to the rafter.

Horizontal Tube

Connection Plate

Rafter

13. After attaching the first two connection plates, flip the 

rafter assembly over and attach the remaining two (2) 

connection plates for the rafter. 

 

ATTENTION:

 Rafters are heavy. Assistants and lifts are 

needed to move the assembled rafters.

14. Repeat the procedures to assembly the remaining 

rafters and related center bracing.

15. After all rafters are assembled, assemble the frame.

Rafter Center

105086

Rafter 

Connection 

Plate

Rafter Connection 

Plate

Содержание PB03020R4






























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды