background image

17

CLEARSPAN

 GARAGES

Revision date: 09.14.10

ATTACH END PANEL ASSEMBLIES

Gather the parts:
•  End panel assemblies
•  Tek screws (#FA4482B) and washers
•  Measuring tape and scissors 

Assembly Procedure:
1.  While standing inside the shelter, start at the peak of 

the end rafter and pull the solid (plain) end panel over 

the top of the rafter so the panel edge is wrapped to the 

inside of the rafter. 

 

NOTE:

 Use additional help to pull the end panel in 

position over the entire rafter. It may be helpful to have 

someone stand on the conduit to keep it on the ground 

when stretching and attaching the end panel.  

 

2.  Move to the lower section of the rafter leg and end 

panel on each side of the rafter, fold the end panel 

material around the rafter tube, and secure it with 

Tek screws and washers on the inside of the rafter  

approximately 12" up from the conduit. 

Attaching the end panel in this manner keeps the 

lower section of the end panel in place as the panel is 

stretched and secured to the rafter. 

 

NOTE:

 The screws are inserted on the backside or 

inside surface of the rafter to prevent damage to the 

main cover when it is installed. 

3.  Evenly space the screws and washers along the rafter 

and pull the end panel tight as the screws are installed.

4.  After securing the lower section of the end panel, move 

to the top, stretch the panel to remove wrinkles, and 

secure it in place as previously described.

12"

5.  Continue attaching the end panel by working evenly 

down both sides of the rafter toward the base frame 

tube. 

 

NOTE:

 If necessary, remove the Tek screws at the 

bottom of each rafter leg to work wrinkles out of the 

end panel and reinstall the Tek screws.

6.  After installing the first end panel, repeat the steps to 

attach the remaining end panel. 

 

NOTE:

 The excess end panel material can be 

removed, or folded under and attached to the rafter 

as described earlier. If the excess is removed, allow at 

least six inches (6") to remain beyond the Tek screws. If 

the panel is removed for any reason, the extra material 

is used to pull the panel tight.

7.  After installing both end panels, install the ratchets.

Содержание PB03020R4






























Отзывы: