ClearSpan Gothic Style Solar Star 104844 Скачать руководство пользователя страница 24

Страница: 24 / 43

CLEARSPAN

™

GREENHOUSES

Revision date: 10.03.14

INSTALL MAIN COVER

Gather the parts:
•  Main covers, inflation fan kit, box cutter or utility knife
•  U-channel spring (#102198)
•  Ropes long enough to reach over the frame (provided

by customer)

Assembly Procedure

After the poly latch U-channel is attached to the frame,

unpack the main cover and pull into place. Ropes or straps

are typically used to pull the main cover onto and over the

frame.

WARNING:

To prevent damage to the cover and to

prevent serious personal injury, DO NOT attempt to

install the main cover on windy or stormy days.

INSTALL POLY LATCH U-CHANNEL (continued)

3. Continue to attach the U-channel sections to the rafters

(or ribbon board if used) and work toward the other end

of the frame. Cut the last section of U-channel to the

required length so that it is flush with the end wall panel

(if needed).

4. Repeat these steps for the remaining side.

5. After

attaching the U-channel to the sides of the frame,

use Tek screws to attach the single U-channel to the

top edge of the end rafters.

Insert shows the installation of poly latch U-channel on

top of an end rafter. The poly latch U-channel will bend

with the curve of the rafter as it is attached.

6. Continue to attach the U-channel until it has been

installed on the top of

both end rafters

The steps that follow describe one way to complete this

process.

ATTENTION: Install the IR film cover first! Examine the

IR film and install with the correct side facing in the

direction indicated on the film.

1. Take the cover film and position it along the base of

one side of the greenhouse.

NOTE:

Unfold the cover and locate the leading edge

The frame shown in the photos that follow differs from

actual frame. Procedure is the same.

Photo shows the cover film in position to pull over the

greenhouse.

2. Along the edge, make small holes in the cover at

evenly spaced intervals and tie rope or straps to the

cover. May not be needed for smaller greenhouses.

NOTE:

The ropes or straps must be long enough to

reach over the top of the building to the other side.

Long buildings require additional ropes to prevent

tearing the main cover when it is pulled into place.

Keep the holes, used to attach the rope or straps, near

the edge of the material and below where the cover will

be secured to the U-channel.

Consult the Spec Sheets for cover identification. The

greenhouse is equipped with double-layer main cover and

an inflation fan kit. One cover is pulled into position and

anchored to the frame, then the inflation kit is installed, and

finally the last main cover is attached.

Top edge of the end rafter

Location of the side runs of U-channel and ribbon board.

Содержание Gothic Style Solar Star 104844












































Результаты поиска

Содержание Gothic Style Solar Star 104844

Отзывы:

Похожие инструкции для Gothic Style Solar Star 104844

Бренды по названию

Популярные бренды

ClearSpan Gothic Style Solar Star 104844, Инструкция по эксплуатации

Результаты поиска

Содержание Gothic Style Solar Star 104844

Отзывы:

Похожие инструкции для Gothic Style Solar Star 104844

Бренды по названию

Популярные бренды