ClearSpan 107769 Скачать руководство пользователя страница 17

Страница: 17 / 25

CLEARSPAN

™

POLY BUILDINGS

Revision Date: 03.13.08

ATTACH MAIN COVER

Gather the parts:
• Main cover (with conduits inserted)
• Ropes (provided by customer) or strap long enough to

reach over the frame

• Box cutter or utility knife

WARNING:

To prevent damage and injury, do not

leave the cover unattended if it has not been properly

secured.

The ropes can be used to temporarily keep

the cover from blowing off the frame.

Assembly Procedure
1. To pull the cover over the frame, attach ropes or straps

to both ends of the cover conduit positioned

furthest

from the frame

. Wrap the rope around the conduit a few

times to prevent it from slipping off.

NOTE:

Depending on the length of the cover it may

be necessary to attach additional ropes to the cover

conduit between the end ropes by cutting a small

opening in the cover pocket and tying the rope around

the conduit. DO NOT cut through the main cover.

Cut

through the conduit pocket only.

2. With all ropes attached to the cover conduit, lift and

carry the conduit and cover toward the base of the

assembled frame.

3. Set the conduit down, toss the ropes over the frame,

and pull the cover into position. Position one person

at each rope.

Verify that the cover pockets are to the

inside of the building. This will be the underside of the

cover when it is pulled into position on the frame.

4. Once the main cover is pulled into position, center the

cover on the frame (end-to-end and side-to-side).

WARNING:

To prevent damage and injury, do not

leave the cover unattended if it has not been properly

secured.

5. Locate the black straps at the front and rear hems and

feed the straps through the center slot in each end

ratchet. Operate the ratchet to wrap the strap onto the

center hub just enough to keep the strap secure.

NOTE:

Use lifts and additional assistants (if needed) to

help pull the cover up and over the frame.

NOTE:

Do not tighten completely at this time. This

helps to temporarily secure the cover.

6. Tie the ropes (or straps), used to pull the cover into

position, to the frame to help hold the cover.

7. Move to the other side conduit of the cover and

temporarily secure that side of the cover to the frame.

NOTE:

Tie short pieces of rope to the ends of the side

conduit and directly across from the ropes or straps

tied to the other side conduit to temporarily secure

the cover to the frame. Once side straps are installed

and slightly tightened, the temporary ropes can be

removed.

8. Position the cover conduit within the pocket so that the

ends do not contact or rub on the bonnet portion of the

main cover. May not apply for some cover designs.

9. Continue with the installation of the side straps.

Photo shows the ratchet

attached to the end

rafter. This ratchet is

used to secure the

bonnet portion of the

main cover.

Main Cover

Bonnet

NOTE:

Cover shown

may differ from the

actual cover for your

building.

Shelter shown above may be a different style or length.

Cover

Conduit

Ropes

Содержание 107769


























Результаты поиска

Содержание 107769

Отзывы:

Похожие инструкции для 107769

Бренды по названию

Популярные бренды

ClearSpan 107769, Руководство пользователя

Результаты поиска

Содержание 107769

Отзывы:

Похожие инструкции для 107769

Бренды по названию

Популярные бренды