manualshive.com logo in svg

ClearSpan 106605, Руководство пользователя

Поделиться
Скачать
ClearSpan 106605 Скачать руководство пользователя страница 15

Visit 

www.ClearSpan.com

 for additional products and customer assistance.

CLEARSPAN

™

 SUNBURST POLY BUILDINGS

1

Using the main cover conduit as a guide, attach the 
ratchets to the rafter leg at the proper height. Fasten 
ratchets to the rafters using a Tek screw.

6.

Once the main cover is pulled into position, center the 
cover on the frame and remove the ropes. Loosely 
secure the ends of the cover to the ratchets attached to 
the front and back end panel conduits. 
 

ATTENTION:

 Do not tighten the straps at this time.

Divide the remaining number of ratchets in half and 
place the ratchets on the ground next to the rafter 
where they will be attached.  
 

NOTE:

 Space ratchets evenly along each side of the 

shelter and directly across from each other on or near 
the 

same rafter assembly

. See the example shown 

below.  
 

Consult the Side Profile diagrams in the Quick Start 
section for the ratchet locations.

4.

5.

NOTE:

 Side view shows where to place ratchets for a 

similar frame. 

Ratchets can be attached either to the base 

conduit or to the rafter leg pipe above the fitting.

ATTACH MAIN COVER

Gather the parts:

Main cover (with conduits inserted)

Ropes long enough to reach over the frame (provided 
by customer)

Ratchets and plain straps

Tek screws

Box cutter or utility knife 

Assembly Procedure

To pull the cover over the frame, attach a rope to each 
end of the cover conduit. Wrap the rope around the 
conduit a few times to prevent it from slipping off. 
 

•

•

•

•

•

1.

NOTE:

 Depending on the length of the cover it may 

be necessary to attach additional ropes to the cover 
conduit between the end ropes by cutting a small 
opening in the cover pocket and tying the rope around 
the conduit.  
 
DO NOT cut through the main cover. 

Cut through the 

conduit pocket only.

With all ropes attached to the cover conduit, lift the 
conduit and carry the cover toward the base of the 
frame.

Toss the ropes over the frame and pull the cover into 
position. One person is required at each rope.

2.

3.

Cover 
Conduit

Ropes

NOTE:

 Diagram above may show a different frame. Cover 

and end panel design may also vary.

NOTE:

 Depending on the cover, strap length, and personal 

preference, ratchets can be attached to the inside or 
outside surface of the rafters or to the base conduit. 

Содержание 106605


























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды