manualshive.com logo in svg

ClearSpan 105589, Инструкция по эксплуатации

Поделиться
Скачать
ClearSpan 105589 Скачать руководство пользователя страница 7

7

CLEARSPAN

™

 CARPORTS

Visit 

www.ClearSpan.com

 for additional products and customer assistance.

ASSEMBLE RAFTERS 

Each rafter consists of three (3) large 2" x 3" rectangular 

pipes, two (2) additional 2" x 2" square tubes, and related 

mounting plates and pipe straps. 

NOTE

: Assistance may be required to assemble the carport 

frame.

 

Gather the parts:
•  Rafter pipe ( #R23P029) 
•  Rafter pipe (#24CP23P1) 
•  Rafter pipe (#105330)
•  Mounting pipe (#105561)
•  Support tube (#S20P066)
•  Pipe strap (#QH1070)
•  2-Way pipe fitting (#104625)
•  Connection plate (#105087)
•  Tek screws  and nut setter (3/8'' x 2-9/16 magnetic)

 

The following steps describe one way to assemble the 

individual rafters. Consult the Front Profile rafter diagram in 

the Quick Start section to view an assembled rafter. 

1.  Position the 2" x 3" rectangular tubes as shown.

2.  Insert the swaged ends into the plain ends of the pipes 

to assemble the main rafter.

Typical Main Rafter Assembly

#R23P029

#105330

#24CP23P1

3.  After connecting the separate pipes, locate two (2) pipe 

straps (#QH1070) and install these as shown. 

Tek screws

ATTENTION: 

The pipe straps are installed on the 

underside of the rafter with one Tek screw on each side 

of the pipe splice as shown below.

4.  Install two additional Tek screws at each pipe joint in 

the location identified above. 

 

NOTE:

 DO NOT TIGHTEN THE PIPE STRAPS AT 

THIS TIME. These are tightened after the purlins are 

installed.

5.  Locate the two (2) square tubing pipes (#105561 and 

#S20P066) and connect these using the 2-Way pipe 

fitting (#104625) as shown. Secure each pipe using a 

Tek screw.

Tek screws

Tek screws

#105561

#S20P066

Содержание 105589




























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды