manualshive.com logo in svg

ClearSpan 105589, Инструкция по эксплуатации

Поделиться
Скачать
ClearSpan 105589 Скачать руководство пользователя страница 16

Visit 

www.ClearSpan.com

 for additional products and customer assistance.

CLEARSPAN

™

 CARPORTS

16

INSTALL THE CORRUGATED ROOF PANELS

The following steps describe one way to install the 

corrugated roof panels.

 

Gather the Parts:
•  Corrugated polycarbonate panels (#104621G)
•  Wall profile (#105521)
•  Neo-bonded galvanized washers (#102921B) 
•  Tek screws and nut setter (3/8'' x 2-9/16 magnetic) 

NOTE:

 The roof panels are installed with their ribs running 

parallel with the rafters

. This allows for proper drainage and 

helps when removing debris. 

All roof panels are secured to the hat channel using Tek 

screws and neo-bonded washers. 

A Tek screw is install along each roof panel edge and in the 

center of each panel on 

every hat channel run

.

1.  Take one corrugated roof panel and position it evenly 

on the frame. 

The edge of the panel will align with the outside edge 

of the rafter when the panel is correctly positioned. 

 

The top of the panel can be set flush with the 

permanent structure or it can remain an inch or so 

away to allow for variations in the structure. Corrugated 

wall profile is installed last to finish the top edge.

2.  Beginning at any of the mid runs of hat channel, take 

a neo-bonded washer and a Tek screw and secure the 

panel to the hat channel. 

 

NOTE:

 Use a chalk line to mark the location of the 

center of the hat channel (if desired). This helps to 

keep the screws aligned. Install all Tek screws and 

washers in the valleys of the panels. 

DO NOT SECURE THE PANEL TO THE UPPER RUN 

OF HAT CHANNEL AT THIS TIME.

3.  Continue to secure the panel along the outside edge 

until a screw has been installed in each run of hat 

channel 

except

 the upper run.

4.  Move to the middle of each hat channel run for the 

first panel, except the upper hat channel, and install 

another Tek screw and washer.

5.  With the first panel secured along the edge and in the 

middle, take the first section of wall profile (#105521) 

and place it against the permanent structure and on top 

of the first roof panel.

6.  Beginning at the outside edge, install a Tek screw and 

washer through the wall profile, through the first roof 

panel, and into the upper run of hat channel.

Tek screw and washer

Содержание 105589




























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды