manualshive.com logo in svg

ClearSpan 104596W, Руководство пользователя, Страница: 16 / 29

Поделиться
Скачать
ClearSpan 104596W Скачать руководство пользователя страница 16

CLEARSPAN

™

 FABRIC STRUCTURES

16

Revision date: 01.23.09

PREPARE AND INSTALL THE MAIN COVER

 

Gather the parts:
•  Main cover, Tek screws, and strap (#103620B) 
•  Pipe 1.315'' x 75'' swaged (#131S075) 
•  Pipe 1.315'' x XX'' plain (#131P0XX)

NOTE:

 Each cover conduit consists of 1.315" x 75" 

(#131S075) pipes (number is determined by shelter length) 

and one (1) 1.315" x XX" (#131P0XX) pipe. 

 

The XX" represents the remaining length required to reach 

the end of the shelter. Consult the Spec Sheet and Side 

Profile diagrams for part identification.

        

WARNING:

 To prevent damage to the main cover 

and prevent serious personal injury, Do not install the main 

cover on a windy day. 

 

Complete these steps to prepare the frame and install the 

main cover:
1.  Check the frame for sharp edges or bolts that could 

damage the cover during installation. Cover these 

surfaces with duct tape or file smooth if necessary.

2.  Locate the pipes for two (2) main cover conduits. See 

Side Profiles for correct pipe lengths.

3.  Connect these pipes by inserting the swaged ends 

of the pipes into the plain ends until each conduit is 

assembled. Secure each pipe joint with a Tek screw 

and wrap the joint with duct tape.  

1˝

These cover conduits are inserted into the pockets 

sealed to the cover. The conduits are used to tighten 

and secure the cover. 

4.  After assembling the cover conduits, locate the cover 

and unfold it on a clean, smooth surface near the 

frame.  

 

NOTE: 

When handling the cover and setting it in  

position, do not pull on the end straps. They will pull out  

of the cover. Unfold the cover with the inside surface 

facing up and the skirt portion positioned toward the 

closed/back side of the frame.

NOTE:

 Shelter shown above may differ in length from 

the actual model. 

7.  To pull the cover over the frame, attach ropes to the 

cover conduit farthest away from the frame. Wrap the 

rope around the conduit a few times to prevent it from 

slipping off. May not be required for small shelters. 

5.  Locate the cover ends with strapping and align cover 

with the shelter frame.

6.  Insert a conduit into each

 cover conduit pocket

 of the 

main cover. 

NOTE:

 Depending on the length of the cover it may 

be necessary to attach additional ropes to the cover 

conduit between the end ropes by cutting a small 

opening in the cover pocket and tying the rope around 

the conduit. DO NOT cut through the cover. 

Cut 

through the conduit pocket only.

8.  With all ropes attached to the conduit, lift the conduit 

and carry the cover toward the base of the frame.

9.  Toss the ropes over the frame and pull the cover into 

position. One person is required at each rope.

Cover Conduits

Cover 

Ends with 

Strapping

Cover Conduit

Cover 

Conduit

Cover 

Skirt

Actual frame 

may differ from 

frame shown.

Ropes

Содержание 104596W






























Отзывы:

Нет отзывов