CleanFreak CF-100 Series Скачать руководство пользователя страница 5

SAFETY INSTRUCTIONS

WARNING!

When using an electrical appliance, basic precautions should always be followed.

To reduce the risk of fire, electric shock or injury following these tips:

1. 

Do not leave appliance plugged in. Unplug from outlet when not in use.

2.  

Electric shock could occur if used outdoors or on wet surfaces.

3.  

Keep away from children. Extractor is not to be used as a toy.

4.  

Use only as described in this manual. Use only manufacturer’s recommended parts.

5.  

Do not use extractor with damaged power cords.

6.  

Do not abuse the power cord. Do not pull or carry extractor with the power cord. Do not use the power cord  

 

as a handle. Do not close doors on the power cord. Do not pull power cord around sharp edges or corners.  

 

Do not run the extractor over the power cord. Do not keep power cords around heated surfaces.

7.  

Do not unplug by pulling on electric power cord. To unplug, grasp the plug, not the electric power cord.

8.  

Do not handle plug or appliance with wet hands.

9.  

Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair and  

 

anything that may reduce air flow.

10.  

Keep hair, loose clothing, fingers and all parts of body away from openings and moving parts.

11.  

Do not pick up anything that is burning or smoking, such as cigarettes, matches or hot ashes.

12.  

Do not use extractors without filters.

13.  

Turn off all controls before unplugging from electric outlet.

14.  

Use extra care when cleaning on stairs.

15.  

Always wear safety equipment and appropriate clothing when operating the extractor. 

16.  

Do not use extractor to pick up flammable or combustible liquids such as gasoline or use in areas where such  

 

items may be present.

17.  

Connect to a properly grounded electric power outlet only.

18.  

Do not attempt to service the extractor while appliance is plugged in.

 

5

Содержание CF-100 Series

























Отзывы: