GOLDEN SCAN 3
7
10. WIRING DIAGRAM
8. TROUBLESHOOTING
9. TECHNICAL DATA
ELECTRICAL/MECHANICAL
SPECIFICATIONS
Power supply
• 220 - 240V 50Hz
• 200 - 220V 60Hz
Lamp
Metal iodide type with special built-in
power supply unit.
• Type of lamp: HMI 1200W
- Cap SFc 15.5-6
- Colour temperature 6000 K
- Luminous flux 110000 lumen
- Average life 750 h
• Type of lamp: HMI 575W
- Cap SFc 10-4
- Colour temperature 6000 K
- Luminous flux 49000 lumen
- Average life 750 h
Power consumption
• HMI 1200 Touring Version
- 1500VA at 220V 50Hz
- correction factor 140µF standard
• HMI 1200 Version
- 3000VA at 220V 50Hz
• HMI 575 Version
- 1500 VA at 220V 50Hz
Motors
N. 9 microstepping motors with full
microprocessor control.
Lamp hourmeter
Incremental non-resettable count. (stan-
dard feature on Touring Version only).
OPTICAL SYSTEM
Optical unit
Main optical unit in diecast alumini-
um, incorporating twin lens con -
denser and a reflector of high lumi-
nous efficiency.
Lens units
• Standard: 1:2,5/250 mm
• Opzionale:1:3,3/300 mm
• Opzionale:1:1,6/160 mm
(to be fitted internally of projector).
CONTROL SYSTEMS
Channels
N. 6 control channels (normal operation)
N. 8 control channels (extended operation)
Inputs
The GOLDEN SCAN 3 is set up to
accept analog or digital signals from
controllers or computers.
• Digital serial input:
RS232/423(PMX) or DMX 512
• 0-10V analog input
MIRROR HEAD
• Head rotatable through 360° on pro-
jector housing.
• Graduated scale for easy and accu-
rate positioning.
• Anchorage for safety wire.
• Mirror of ultra high luminous efficiency.
Movement
• Produced by two µ P controlled
microstepping motors.
• Infinitely variable speed of rotation;
maximum values:
- PAN = 0.4 sec (150º)
- TILT = 0.3 sec (110º)
• Continuous and uniform movement.
Resolution:
PAN = ±0.3° (150°)
TILT = ±0.2° (110°)
Safety devices
• Power supply shuts off automatically
in the event of overheating or cooling
system failure.
• Power shuts off automatically when
cover is opened.
Cooling
Forced ventilation cooling system
using axial flow fans.
Housing
• Extruded die-cast aluminium.
• Epoxy powder coated finish.
• Four side handles
(standard feature on Touring
Version only).
Mounting
• Steel bracket with epoxy powder
coated finish.
• Six installation positions, 25 mm (1”)
apart.
• Bracket adjustable through 100° with
graduated scale to assist positioning.
• Anchorage for safety wire.
Operating position
Will function in any position.
(14.4”)
365
(48.4”)
1230
(17.1”)
435
(14.2”-17.1”)
360-435
No electrical power supply.
Lamp expended or faulty.
Check that power is available at
the mains socket
Signal transmission cable
short-circuiting or disconnected.
Change cables.
Change lamp (see instructions).
Address codes incorrect.
Defect in electronic circuits.
Contact an authorized technician.
Lenses broken.
Contact an authorized technician.
See projector coding instructions.
Deposit of dust or grease.
Clean (see instructions).
PROJECTOR DOES NOT LIGHT UP
ELECTRONICS NOT WORKING
FAULTS
PROJECTION FAULTY FAULTS
REDUCED BRIGHTNESS
POSSIBLE CAUSES
CHECKS AND REMEDIES
•
•
•
•
•
• •
•
•
Weights and dimensions
• HMI 1200 TV 36.4 kg (80 lbs 1 ozs)
• HMI 1200:
35.5 kg (78 lbs 2 ozs)
• HMI 575:
29.5 kg (64 lbs 14 ozs)
• Mirror head
3.1 kg ( 6 lbs 13 ozs)
The products referred to in this manual comply with EC
Directives on:
• Low Voltage 73/23
• Electromagnetic Compatibility 89/336
The specifications published in this manual are not binding, and may be revised or updated
at any time by Clay Paky without notice in the interests of improving product quality.
