CLAS OH 7014, Руководство пользователя

Страница: 19 / 28

OH 7014
EXTRA FLAT TROLLEY JACK 3T 75mm
PREVENTATIVE MAINTENANCE
This is the safety alert symbol used for the PREVENTATIVE MAINTENANCE section of this
manual to alert you to potential personal injury hazards. Obey all instructions to avoid possible
injury or death.
1. Always store the jack in a well protected area where they will not be exposed to inclement
weather, corrosive vapors, abrasive dust, or any other harmful elements. The jack must be
cleaned of water, snow, sand, grit, oil, grease or other foreign matter before using.
2. The jack must be lubricated periodically in order to prevent premature wearing of parts.
A general purpose grease must be applied to all zerk grease fittings, caster wheels, front
axle, lift arm, handle base pivot bolts, release mechanism and all other bearing surfaces. Worn
parts resulting from inadequate or no lubrication are not eligible for warranty consideration.
3. It should not be necessary to refill or top off the reservoir with hydraulic fluid unless there is
an external leak. An external leak requires immediate repair which must be performed in a
dirt-free environment by an authorized service center.
IMPORTANT:
In order to prevent seal damage and jack failure, never use alcohol, hydraulic brake
fluid or transmission oil in the jack. Use Chevron Hydraulic Oil AW ISO 32 or its equivalent Unocal
Unax AW 150.
4. Every jack owner is responsible for keeping the jack labels clean and readable. Use a mild
soap solution to wash external surfaces of the jack but not any moving hydraulic components.
5. Inspect the jack before each use. Do not use the jack if any component is cracked, broken,
bent, shows sign of damage or leaks hydraulic fluid. Do not use the jack if it has loose or
missing hardware or components, or is modified in any way. Take corrective action before
using the jack again.
6. Any hydraulic repairs within the warranty period must be performed by an authorized service
center.
Raising the Jack
Lowering the Jack
1. Block the vehicle’s wheels for lifting stability.Secure the load to prevent inadvertent shifting and movement.
2. Position the jack near desired lift point.
3. Set the Parking Brake in the vehicle.
4. Refer to the vehicle manufacturer owner’s manual to locate approved lifting points on the vehicle.Position the jack so that the saddle is
centered and will contact the load lifting point firmly.Raise jack by pumping handle until desired height is reached. After lifting, secure and
transfer load to jack stands or other appropriate means. Do not use jack as the only means of support.
5. Assemble the handle; ensure to align with slots.
6. Close the release valve by turning it clockwise until it is firmly closed.
7. Before raising the vehicle double check and verify the saddle is centered and also has full contact with the lifting point.
8. Pump handle to lift until saddle contacts load.Continue to pump the jack handle to lift the vehicle to the desired height. After lifting, support
the load with appropriately rated vehicle support stands before working on the vehicle.
1. Raise load high enough to allow clearance for the jack stands to be removed, then carefully remove jack stands.
2. Remove support stands.
3. Grasp the handle firmly with both hands. Securely hold on to the jack handle so your hands do not slip and ensure the release valve does
not rapidly lower.
4. Carefully open the Release Valve by slowly turning the handle counter-clockwise. (Do not allow bystanders around the jack or under the
load when lowering the jack.
5. After removing jack from under the load, keep jack in the lowered position to reduce exposure to rust and contamination.
NOTE: Always store jack in the fully lowered position, and the handle in the upright position
PREVENTATIVE MAINTENANCE
This is the safety alert symbol used for the PREVENTATIVE MAINTENANCE section of this manual to alert you to potential personal
injury hazards. Obey all instructions to avoid possible injury or death.
1. Always store the jack in a well protected area where they will not be exposed to inclement weather, corrosive vapors, abrasive dust, or
any other harmful elements. The jack must be cleaned of water, snow, sand, grit, oil, grease or other foreign matter before using.
2. The jack must be lubricated periodically in order to prevent premature wearing of parts. A general purpose grease must be applied to all
zerk grease fittings, caster wheels, front axle, lift arm, handle base pivot bolts, release mechanism and all other bearing surfaces. Worn
parts resulting from inadequate or no lubrication are not eligible for warranty consideration.
3. It should not be necessary to refill or top off the reservoir with hydraulic fluid unless there is an external leak. An external leak requires
immediate repair which must be performed in a dirt-free environment by an authorized service center.
IMPORTANT: In order to prevent seal damage and jack failure, never use alcohol, hydraulic brake fluid or transmission oil in the jack.
Use Chevron Hydraulic Oil AW ISO 32 or its equivalent Unocal Unax AW 150.
4. Every jack owner is responsible for keeping the jack labels clean and readable. Use a mild soap solution to wash external surfaces of the
jack but not any moving hydraulic components.
5. Inspect the jack before each use. Do not use the jack if any component is cracked, broken, bent, shows sign of damage or leaks
hydraulic fluid. Do not use the jack if it has loose or missing hardware or components, or is modified in any way. Take corrective action
before using the jack again.
6. Any hydraulic repairs within the warranty period must be performed by an authorized service center.
Linkage Lifting Arm Handle Socket Rolloer Pin
Linkage Lifting Arm Handle Socket Rolloer Pin