Clarke Woodworker CTS14 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 28

Clarke Woodworker CTS14 Скачать руководство пользователя страница 21

21

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

MAINTENANCE

• Remove dust and dirt regularly from the machine. Cleaning is best

carried out with a fine brush or a cloth.

• Never use caustic agents to clean plastic parts.

• Keep the saw unit clean.

CLEANING THE THREADED RODS

This operation should be carried out at least once a year

1. Place the machine on its side.

2. Remove the base plate by undoing the screws.

3. Clean the threaded rods and lubricate them with a multi-purpose grease.

REPLACING THE CARBON BRUSHES (ITEM 127 IN THE PARTS LIST)

Check the carbon brushes every 10 operating hours. If the length of the
carbon brushes is less than 5 mm, you should change them to prevent
damage to the motor.

1. Move the saw blade to its lowest position.

2. Place the machine on its side.

3. Remove the base plate.

4. Unscrew the carbon brush covers.

5. Inspect the carbon brushes and, if necessary replace them.

6. Replace the base plate.

• Allow the machine to run for a few minutes to allow the carbon

brushes to run in.

WARNING: REMOVE THE PLUG FROM THE MAINS POWER SUPPLY BEFORE
CARRYING OUT ANY ADJUSTMENT. SERVICING OR MAINTENANCE

CAUTION: CARBON BRUSHES MUST BE REPLACED IN PAIRS

«
...
19
20
21
22
23
...
»

Содержание Woodworker CTS14





























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды