background image

3

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

SAFETY INSTRUCTIONS AND WARNINGS

PLEASE READ THESE INSTRUCTIONS CAREFULLY AND KEEP THIS INSTRUCTION 
MANUAL SAFE FOR FUTURE USE.

SAFETY INSTRUCTIONS AND WARNINGS

1. Maintain the dolly in good condition. Keep it clean for best and safest 

performance. 

2. The maximum load is 567Kg (1250 Lbs). DO NOT exceed this rated 

capacity.

3. Use this dolly for supporting motorcycles only. DO NOT use it for any other 

purpose.

4. Do not stand, sit or ride on the dolly.

5. Keep children and unauthorised persons away from the work area.

6. When using this dolly to support a motorcycle DO NOT leave unattended if 

there is a chance of children or others entering the area.

7. Keep proper balance and footing, do not overreach, wear nonslip 

footwear.

8. Only use the dolly on a surface that is flat, stable, level, dry and not 

slippery, and capable of supporting the load.

9. Lower the handles on Carriage A and Carriage B when not in use.

10. Store the dolly in a safe, dry place and keep away from children.

11. DO NOT operate the dolly when you are tired or under the influence of 

alcohol, drugs or any intoxicating medication.

12. DO NOT make any modifications to the dolly.

13. DO NOT expose the dolly to rain or snow.

14. If the dolly needs repairing and/or there is any part which needs to be 

replaced, have it repaired by a technician and only use replacement 
parts supplied by the manufacturer. 

WARNING: THE WARNINGS, CAUTIONS AND INSTRUCTIONS DISCUSSED IN 
THIS INSTRUCTION MANUAL CANNOT COVER ALL POSSIBLE CONDITIONS 
AND SITUATIONS THAT MAY OCCUR. IT MUST BE UNDERSTOOD BY THE 
OPERATOR THAT COMMON SENSE AND CAUTION ARE FACTORS WHICH 
CANNOT BE BUILT INTO THIS PRODUCT, BUT MUST BE SUPPLIED BY THE 
OPERATOR.

Содержание MCD1









Отзывы: