background image

Clarke

®

  Operator's  Manual  -  BOOST  28

                                              Page  -21-

Maintenance Procedures To Be Done Every Week:

WARNING:  Maintenance and repairs must be done

by authorized personnel only.  Always
empty the solution tank and the
recovery tank before doing any
maintenance.  Keep all fasteners tight.

WARNING:  Always wear eye protection and

protective clothing when working near
batteries.  Do not put tools or other
metal objects across the battery
terminals or the tops of the batteries.

CAUTION:   To prevent damage to the machine, and

discharge across the tops of the
batteries, do not fill the batteries above
the bottom of the tube in each cell.
Wipe any acid from the machine or the
tops of the batteries.  Do not add acid to
battery after installation.

NOTE: 

Always turn off key switch before servicing the

machine.

WARNING: Always wear eye protection and

protective clothing when working near
batteries.  NO SMOKING!

1.  To inspect batteries, tip up recovery tank until it locks in

the full open position.  See figure 27A.  To close the tank,
pull up on the latch arm and then slowly lower the tank to
the closed position.

CAUTION: Before raising the tank, be sure tank is

empty.

NOTE: 

There is an intermediate position available for holding

the recovery tank open for charging batteries.  See figure 27B.

WARNING:  Do not operate or perform

maintenance on the machine while
the recovery tank is in the
intermediate position.  The tank can
be accidentally bumped and it may
slam shut.

2.  Disconnect the batteries.  Use a cloth and a solution of

ammonia or bicarbonate of soda to wipe the top of the
batteries.  Clean the battery terminals.    Reconnect the
batteries.

3. Check the hoses for leaks, obstructions and other

damage.

4.  Use a grease gun to lubricate the dual casters.

See figure 28.

 Maintenance

Figure 27A

Figure 27B

Figure 28

Содержание Focus II Mid-Size Autoscrubber Boost 28

























































Отзывы: