background image

5

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

THE TABLE TOP

1. Turn the table top face 

down and attach the 
two drawer runners as 
shown in fig 4, using 
three wood-screws 
each side in the pre-
drilled holes in the table 
top.

2. The table is now ready 

to be assembled to the 
cabinet.

3. With the table top remaining face down, position the cabinet on top with 

the feet uppermost.

NOTE: The front of the table top is the edge closest to the drawer runners. 

Take care to align this with the front of the cabinet.

4. Line up the holes in the legs with the pre-drilled holes in the table top and 

locate with wood-screws. Tighten fully.

5. Turn the structure back onto its feet.

THE DRAWER & SHELF

The drawer comprises:

2 x Side Panels, I x Front Panel, 1 x Back Panel, 1 x Bottom Panel

1. Having identified the various 

parts as in Fig 5, bolt the side 
panels to the front panel as 
shown, then add the back 
panel with all fastenings only 
finger tight.

2. Drop in the bottom panel and 

secure with bolts, nuts and 
washers.

3. Ensure the drawer is square 

before tightening all the nuts.

4. Slide the drawer into place beneath the table top.

5. Position the shelf on the shelf supports.

Your workbench is now fully assembled and ready for use.

Содержание CWB1250









Отзывы: