background image

Thank you for selecting this CLARKE 1/3 Sheet Orbital Sander, which is designed for DIY  use
only.

Before attempting to use the machine, please read this leaflet thoroughly and follow the
instructions carefully. In doing so you will ensure the safety of yourself and that of others
around you, and you can look forward to the Sander giving you long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12 months from the
date of purchase. Please keep your receipt therefore, as proof of purchase.

This guarantee is invalid if the product is found to have been abused or tampered with in
any way, or not used for the purpose for which it was intended.

Faulty goods should be returned to their place of purchase, no product can be returned to
us without prior permission.

This guarantee does not effect your statutory rights.

Please note that the backing pad is not covered by this warranty.

For Spare Parts and Service,please contact your nearest dealer, or CLARKE International,

on one of the following numbers.

PARTS & SERVICE TEL:  020 8988 7400

PARTS & SERVICE FAX:  020 8558 3622

or    e-mail as follows:

PARTS:   [email protected]

SERVICE:    [email protected]

PARTS  & SERVICE

3

Содержание COS200












Отзывы: