Clarke COS200 Скачать руководство пользователя страница 8

Страница: 8 / 11

TROUBLE SHOOTING

Sander is overheating

This indicates the machine is dirty. Clean the ventilation holes, and blow
out with compressed air or a clean dry cloth.
Overloading the machine will also cause overheating. Do not use for
heavy duty work, and do not apply excessive pressure.

Excessive sparking occurs

This indicates worn brushes. This problem is quickly remedied but you should
consult your CLARKE dealer for parts and advice.

Sander does not operate when switched ON

Check to ensure the fuse is sound, and replace if necessary. If the fuse is
sound, or the blows repeatedly, consult your CLARKE dealer.

MAINTENANCE

Always inspect the machine before use, and ensure it is in top condition.

Ensure all air vents are clear, (use compressed air to clean the machine where possible).

Check the cable to ensure it is sound and free from cracks, bare wires etc.

RENEWING THE BASE PLATE

Ensure the machine is disconnected from the mains supply, then unscrew the four screws
securing the plate to the machine.

Replace the plate and reassemble ensuring you DO NOT overtighten the four screws.

Содержание COS200












Результаты поиска

Содержание COS200

Отзывы:

Похожие инструкции для COS200

Бренды по названию

Популярные бренды

Clarke COS200, Инструкция по эксплуатации и обслуживанию

Результаты поиска

Содержание COS200

Отзывы:

Похожие инструкции для COS200

Бренды по названию

Популярные бренды