background image

Please note that the details and specifications contained herein, are correct at the time of going to

print. However, CLARKE International reserve the right to change specifications at any time without

prior notice

.

SPECIFICATIONS

Elec. Supply ........................................................................... 230V 50Hz 1 ph

Power Rating ......................................................................... 150 Watts

Fuse Rating ............................................................................ 5 Amps

No Load Speed ..................................................................... 10,000 RPM (Orbits/min)

Dust Extraction Port Dia. (Inner/Outer) .............................. 31/38mm

Pad Size .................................................................................. 1/3rd Sheet

Noise Level (Sound Pressure Level) .................................... 72.6dB(A)

Vibration emissions (measured) ..........................................

12.755 m/s

**

** See notes on page 11

When disposing of this product, do not dispose of with general waste. It must be disposed of according
to the laws governing Waste Electrical and Electronic equipment, at a recognised disposal facility.

2

Содержание COS200












Отзывы: