Clarke CMPS2 Скачать руководство пользователя страница 11

Страница: 11 / 16

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

3. Take care that the sharpening

angle matches the existing
bevelled angle of the blade tip.
This avoids removing too much
metal unnecessarily and keeps
the plane blade at its optimum
cutting angle.

4. Adjust it to suit and set the angle

securely using the adjusting knob.
Note the angle on the scale
before tightening.

5. Switch the power unit on.

6. Slide the blade and plate with

light, steady pressure, back and
forth across the grinding wheel in
a continuous motion.

• Do not hold the blade

stationary as this will cause irregular sharpening.

7. Gradually ease the blade down the plate while sharpening. Press very

gently, repeating each step.

8. Lift the blade away and check that the bevelled edge and tip are evenly

sharp across the blade width. If not, adjust the grinding angle and try
again.

9. Use the extra side guide to act as

a spacer when sharpening narrow
chisels.

10. Switch the power unit off and

ensure the grinding wheel has
stopped before removing the
sharpener attachment from the
base unit.

• It is recommended that after

grinding, the chisel or plane
blade tip is honed using an oiled stone.

Содержание CMPS2

















Результаты поиска

Содержание CMPS2

Отзывы:

Похожие инструкции для CMPS2

Бренды по названию

Популярные бренды

Clarke CMPS2, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание CMPS2

Отзывы:

Похожие инструкции для CMPS2

Бренды по названию

Популярные бренды