manualshive.com logo in svg

Clarke CBS250B, Оригинальное руководство пользователя

Поделиться
Скачать
Clarke CBS250B Скачать руководство пользователя страница 18

18

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

2. Loosen the tracking control lock 

and manually rotate the upper 
wheel, taking care of the sharp 
blade

3. Turn the tracking control knob 

clockwise or anticlockwise until 
the saw blade tracks centrally on 
the rubber tyre.

4. After adjusting, retighten the 

tracking control lock and close 
the doors.

ADJUST THE GUIDE/THRUST BEARINGS AND LOWER BLADE GUIDES

The guide/thrust bearings and the lower blade guides help keep the blade 
tracking straight and correctly alligned during use. To adjust:

UPPER GUIDE BEARINGS

1. Loosen the two grub screws.

2. Adjust the bearings so that they 

are approximately 0.5 mm from 
the blade.

3. Retighten the grub screws.

REAR THRUST BEARING

1. Loosen the grub screw.

2. Adjust the bearing so that it is 

approximately 0.5 mm from the 
blade.

3. Retighten the grub screw.

LOWER BLADE GUIDES

1. Loosen the two grub screws.

2. Adjust the guides so that they are 

approximately 0.5 mm from the 
blade.

3. Retighten the grub screws.

Содержание CBS250B





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды