Clarke CAT131 Скачать руководство пользователя

Страница: 9 / 16

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

OPERATING THE IMPACT WRENCH

1. Locate the socket over the nut to

be tightened or loosened.

2. Squeeze the trigger to start the

wrench.

3. Release the trigger switch to stop

the wrench.

• The square drive shaft will

continue to rotate very briefly
after the trigger has been
released.

ADJUSTING THE POWER

1. To adjust the power, set the air

regulator to one of the 3 settings
available. (Setting 1-Low, 3 -High)

• These numbers are only for

reference and do not denote a
specific amount of power.

For maximum power when removing
stubborn nuts, turn the supply
regulator to its highest setting.

DISCONNECTING THE AIR SUPPLY

1. Do not disconnect the air supply hose until the compressor has been shut

down and the compressed air released.

2. Refer to the compressor instruction manual for the procedure to shut down

and vent the compressed air.

3. Once the pressure has been released, disconnect the air supply hose from

the air tool.

Содержание CAT131

















Результаты поиска

Содержание CAT131

Отзывы:

Похожие инструкции для CAT131

Бренды по названию

Популярные бренды

Clarke CAT131, Инструкция по эксплуатации и обслуживанию

Результаты поиска

Содержание CAT131

Отзывы:

Похожие инструкции для CAT131

Бренды по названию

Популярные бренды